What did you buy today

[BigRAWesty]

I'm really struggling to find some sorta flush pannel mount air fitting now though......
I may just need to have a regular fitting...

[threedogs]

You may need to tig weld a recessed one if you know what I mean.
About 100mm x 100mm plate,,, You know,,, just flicking ideas at you

[BigRAWesty]

You may need to tig weld a recessed one if you know what I mean.
About 100mm x 100mm plate,,, You know,,, just flicking ideas at you

That's what I'm thinking.. I do have plenty of stainless in the shed..

And pm replied mate.

[threedogs]

That's what I'm thinking.. I do have plenty of stainless in the shed..

And pm replied mate.

Sooooooooooooooooooooo,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,? lol
You know it will 1 look good and 2 every one will want one
Could even fit a pressure gauge there as well or run one up
to the cabin area
What have you done to that pull out tab area in the back??

[BigRAWesty]

Not accessible with the draws. The metal sides don't allow access..
I was looking at something like this..


But it would make the hose only usable in my car..

[threedogs]

Wouldn't you use the female end with a 1/2" bsp washer holding it tight.
On the troopy I had outlets front and rear, but you need to terminate them
with a female fitting, Then your air hose has the nitto male fitting one end
and a nitto female the other end, That way all your tools will have a Nitto
male screwed to them. Hope that makes sense <<<<<<<<<<<<<<<??
So basically your air gun[blower] your rattle gun, and inflation tool will all
have a male nitto fitted to them, All you need is a short piece of high pressure hose
that will reach all wheels with a female at one end and male nitto at the other end.
Length is normally about 2.2 mtrs long
At the back I had air and water very handy indeed

[BigRAWesty]

Wouldn't you use the female end with a 1/2" bsp washer holding it tight.
On the troopy I had outlets front and rear, but you need to terminate them
with a female fitting, Then your air hose has the nitto male fitting one end
and a nitto female the other end, That way all your tools will have a Nitto
male screwed to them. Hope that makes sense <<<<<<<<<<<<<<<??
So basically your air gun[blower] your rattle gun, and inflation tool will all
have a male nitto fitted to them, All you need is a short piece of high pressure hose
that will reach all wheels with a female at one end and male nitto at the other end.
Length is normally about 2.2 mtrs long
At the back I had air and water very handy indeed

Yea I probably will as they do have a female pannel mount fitting..
Only going the one outlet in the cabin now..
Dropped the other idea.. keeping it simple..

[Touses]

Apparently, today I bought a resleeved block, tested and revalved head, a balanced crank,

Balanced flywheel and clutch, 3" exhaust and a garrett 2863 turbo. Apparently!

My wallet hurts. I'm going home to drink beer.

[threedogs]

Brought some twist lock weatherproof 2 core connectors,
Trying something different fo my awning lights, 6 watt coloured cob lights
Ill put the link later,,, these connectors are perfect for any outdoor project
I only brought 2, wish I'd brought more.

http://www.ebay.com.au/itm/251913657...%3AMEBIDX%3AIT

[mudski]

Apparently, today I bought a resleeved block, tested and revalved head, a balanced crank,

Balanced flywheel and clutch, 3" exhaust and a garrett 2863 turbo. Apparently!

My wallet hurts. I'm going home to drink beer.

Zoom zoom! It will be worth it though.
I just bought two new brew head seals for my coffee machine... Lol. I need ma coffee!