OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

User Tag List

Results 1 to 5 of 5

Thread: Help with error code po201

  1. #1
    Advanced
    Join Date
    Nov 2012
    Posts
    44
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Unhappy Help with error code po201

    My 2007 3litre auto patrol suddenly started running like it has only 3 cylinders almost no power the scan gauge shows an error code of po201.....does anyone know what this code represents....also engine management light is on....have cleaned the maf unit with no effect...

  2. #2
    Advanced
    Join Date
    Jun 2012
    Location
    Pakenham Victoria
    Posts
    47
    Thanks
    9
    Thanked 18 Times in 13 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Google is your friend mate.
    Injector cylinder 1
    P0201 means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled "low" or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or "high". If it doesn't see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
    The causes could be any of the following:

    Bad injector. This is usually the cause of this code but doesn't rule out the possibility of one of the other causes
    Open in the wiring to the injector
    Short in the wiring to the injector
    Bad PCM

  3. #3
    Advanced
    Join Date
    Jun 2012
    Location
    Pakenham Victoria
    Posts
    47
    Thanks
    9
    Thanked 18 Times in 13 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Pepper

    Sorry forgot the next bit.

    Possible Solutions
    First, using a DVOM check the resistance of the injector. If it isn't within specs, then replace the injector.
    Check for voltage at the fuel injector connector. It should have 10 volts or more.
    Visually check the connector for damage or broken wires.
    Visually check the injector for damage.
    If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector.
    At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you're not sure, do not attempt) The injector should activate
    Replace the injector

    Wazza

  4. #4
    Advanced
    Join Date
    Nov 2012
    Posts
    44
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    wazza,you are correct,checked with uncle google and found exactly what you suggested..all fixed now,didnt realise you could simply enter "nissan error code xyz "into google and get a response.
    Thankyou for taking the time to reply.
    Certainly better than nissans responce of "we are booked out till next monday ask nissan assist to truck it in then" meaning no vehicle to use for about a week .....

  5. #5
    Advanced
    Join Date
    Jun 2012
    Location
    Pakenham Victoria
    Posts
    47
    Thanks
    9
    Thanked 18 Times in 13 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Pepper,
    Glad that you got it fixed.

  6. The Following User Says Thank You to Wazza_66 For This Useful Post:

    Avo (15th August 2013)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •