Hi all
Rebuilding my rear brake calipers and found the left hand side axle seal is leaking. Looking at eBay there's heaps of seals, can anyone point me to the one I need? Car is a 92 gq patrol efi with rear disk brakes. Also what's involved with replacing the seal? I feel comfortable to pull it all apart, my only problem is that this is my daily driver and I don't want to find out that I need a specialist tool or other parts to do the job.
Any help will be much appreciated! Thanks all!
Andy
I done mine recently. You will need a seal puller as the seals are pretty damn tight and can be hard to remove. You will also need a drift or some pipe the size as the outside of the seal to tap it in straight with a hammer. I got my seals from a local parts supplier, bursons, repco etc. or you could try Garry at Nizzbits in the vendor section. You are chasing a rear inner axle seal.
Parksy (29th March 2013)
Cheers dominator. Looking at the manual, there appears to be an oil seal and a grease seal. Oil seal being the inner one and the grease one being the furthest out, closest to the hub. So you're saying I need the oil seal?
How was the actual job? Wheel off, caliper, disk, disk shield, caliper adapter, then pull it all out? Will I find the seal inside the diff or will it come out with the axle?
I take it the bearings are lubed using grease as opposed to diff oil in these rigs?
Cheers
When I did the seals on my trol, the oil was coming out of the grease seal, but a mech said that if I packed a heap of grease into the bearings while the axle was out, the grease seal should be ok. And the oil seal is butted against a step in the axle housing or tube and the axle slides through it. After it is replaced you have to take great care to not let the axle rest on it as you slide it back in. If you want to get the grease seals done you may have to get them done by a mech with the correct tools (hydraulic press etc.) Its up to you.
Last edited by mudnut; 29th March 2013 at 09:53 PM.
My advice is: not to follow my advice.
Parksy (30th March 2013)
Cheers mudnut. I forgot to ask dominator, but what does this seal puller look like? Any substitutes for this tool? Cheers.
Check here mateOriginally Posted by Parksy
eBay Search - "Seal Puller"
they will be a Biatch to get out without this tool
they can also be a bugger to install without the correct seal die.
Have a look at THESE
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy --> MudRunnerTD's GQ From the Ground Up
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
Sorry mudrunner, those links don't seem to work for me. I ended up buying a seal puller from autobarn. Looks like some sort of hook/ prying tool.
I ended up using a really big screwdriver and a thin bit of wood on the leverage point to extract the seal. From memory, I used a huge socket and extension to re seat the seal, using a mallet.
My advice is: not to follow my advice.
Sounds like a fairly straight forward job, will get into it as soon as I get some seals.
Are these the correct ones?
http://www.ebay.com.au/itm/Nissan-Pa...#ht_4104wt_922
Cheers
I probably should have mentioned, it is imperative to make sure you drive the seal in evenly, as they tend to kick at an angle.
My advice is: not to follow my advice.
Posting Permissions
Reply With Quote