Hi Ian,
yeah the fuse blows when i had the control unit plug in,
i havnt chased up any further yet, but if all i need is to replace this to get the glowies going again , all will end up good.
Thanks for checkin out the thread
p.s.s, all the dash lights worked and fuel amp temp workin.
forgot to look at radio, have tacken batt out to top up on charger
Last edited by rockndot; 8th January 2012 at 08:22 PM.
That's great news, good job mate.Originally Posted by rockndot
You will need to fit the correct 65 amp fuse ASAP.
If that 15 amp fuse only blows when the glow plug timer is connected then yes it is stuffed.
You have a couple of options.
1. Replace the unit.
2. Pull the cover off the unit and inspected it, it might be repairable. It might have a diode that is designed to blow when the battery is connected up in reverse. If so, it would be mounted on the circuit board closes to the plug and one end will be connected to an earth and the other end will be connected to the ignition wire (just follow the wires through the plug and onto the circuit board). Have a look and see if anything in this area is blown or you can see black arc marks. You may need to try and post some pictures.
3. You can just mount a momentary push button switch in the dash, we can then wire it up so you turn the ignition on, hold down the button for the 10-15 seconds and then start the old girl up.
Cheers
Rodney
In automotive use the fuse main purpose is to protect the vehicle wiring from overheating and catching on fire if a short in the circuit occurs.
They are know as a slow blow fuse and even though they have a rating of say 15 amps under the right conditions it might not blow until it reaches 18 amps.
ECUs will have protection built in them for under voltage supply, over voltage supply and voltage spikes.
What Rodney said X2
The supply fuse at the distribution or fuse panel protects the wiring which is why many are all the same values.
If the equipment requires protection that is accomplished either internally or with a fuse holder on the back or possibly a few inches along the supply cable.
Dolphins are so smart that within a few weeks of captivity, they can train people to stand on the very edge of the pool and throw them fish.
thanks for the follow up guys , great reading/info.
will remove the said controll unit today and have a gander Rodney.
p.s. i just got your tag.....der....i'm slow i know.
p.s.s whats the go uploading photos ?
screen ask me for a url ..?
cheers rock
Last edited by rockndot; 9th January 2012 at 02:50 PM.
Hi Rodney,
i got the little green box out ECU, and checked all out
Wires and circut board look clean as, brand spankin clean, been no issue there
I didn't get into town today to get a few more fuses, and the multi meter should be here tomorrow,
so would like to plug the fuse back in, and see if it blows again,
but had to move her and use her today arround the block.
will keep you updated.
p.s. got the picture thing happening.thanks
well guys,
Plug all back in and still blows that 15 amp fuse , so the box must be knackered, although nothing looked burnt or damaged.
Might need to get a temperary glow thing happening, until i chase another unit.
Wondering if someone could explain how to,
Cheers rock
The connector that plugs into the glow plug module should be a 10 pin connector, 5 pins on the top and 5 pins on the bottom.
With the top row of pins there should be only 2 pins that are being used, 1 pin should have a brown wire in it (this is the ignition feed from the 15 amp fuse you keep blowing) and the other wire colour should be Green wire with a White trace, (this wire connects to the glow plug relay).
All you need to do is connect two wires, one to the brown wire and one to the Green with a White trace and then connect the other end of the wires to your momentary push button switch.
To test, connect your test light or voltmeter onto one of the glow plugs or busbar, turn ignition on and then push the switch in.
The test light or voltmeter should now light up or show about 12 volts.
I would use a good quality momentary push button switch, the last thing you would want is the contacts in the switch to short together causing the glow plugs to stay on.
If you intend on having this permanently setup with the switch, we can add a warning light into the circuit.
Thanks Rodney,
You got a knack for speaking plain english to us not Yet educated,
I got the geist here, will call in to parts shop next day or two,
this may be a longer install, than i would hope, but plenty of other bridges to......yahdah ya
Might like to add that light,
would that just be added on glow plug side of switch ?
The light gets a little bit more tricker.
Yes you could just purchase a small warning light and wire it on the glow plug side of the switch.
But what you really want to know is, if the power is getting to the glow plugs (not just on the other side of the switch).
There is a another wire in the connector ( White with a Blue trace) that powers up when the glow plugs have power (this will show you that the glow plug relay and fusible link are working).
Now if you want to use the original warning light in the dash, this light switches earth, so we would need to use a relay.
It's easy enough, you will just need to get a relay.
rockndot (11th January 2012)
Posting Permissions
Reply With Quote