Search:

Hi Guys
I recently tried to order some parts online and gave them my vin number JN1TCSY61A0365889 and Engine number TD42509988T as suggested to make sure i got the right parts
for my 2006 TD42Ti,...

Thanks for that mate i was not sure if it was indeed globes or LED's whatever which means it should be easy to replace if i can get inside, BUT i have tried to get behind the dash to have a look and...

Hi Guys

I had my 2006 TB42Ti Dash Board replaced under a recall a couple of years back due to the old melt down / wrinkle affect and did not notice for several months that when in 4x4 on the beach...

Hi Guys

My 2006 Patrol developed the wrinkled dash a year or so after i brought it and i thought it might have been caused by the extreme heat of living in the northwest of WA at that time (ave...

Well guys your both right on the money, just like changing a bloody light bulb with a bayonet fitting, thank you for your wisdom.

Spending half the afternoon trying to pull the lower dash panel off my car to remove a dead snake that my sons lost about 2 months ago that has started to stink like you wouldn't believe AND failing...

Hi Guys

I need to remove the lower dash panel under the steering wheel that surrounds the fuse box, bonnet latch, fuel latch etc on my TD42i, i found all the usual bolts and screws, but i cannot...

Send Yendor a PM as he is the electrical guru i believe

I positioned my Great White bar in approx the same position as your original pic and and welded a small piece of U channel over the mounting bolts to prevent interested parties from even thinking...

Good stuff mate i am glad to be able to help someone else for a change

I must be one of the slow learners as well as it had me stuffed, but thanks for the help i needed it.
Check your PM
Mojo

Your a Bloody legend Yendor, that did the trick and no surprises this time
Thanks for the help i would have been stuffed without it.....i think it's time to avoid Toyota wiring for a while
Cheers...

No worries mate i will try that and see what happens.
I believe negative switching was to prevent you from loosing both headlights if you get a problem with the system....i wonder if it is worth the...

64815

Here is the original diagram

Here is the original wiring Diagram
64814

64813

I will try again with my attachment

Hi Yendor

If you turn the spotlight switch off when high beam is on the spotlight turns off as normal
The Spotlight switch is a Rocker type switch from Auto One and the only wire connected off it...

Hi Yendor

I didn't realize you were so thirsty, those first 6 didn't even touch the sides.
I tested the spotlights and they worked fine on high beam and went off on low beam as normal so i left...

Hi Yendor

Decided to work at night as it is cooler, fitted the LED spotties wired up as per your instructions and away they went first time, no smoke no flames no problems so i must have got it...

Thank you very much for that Yendor that solves my problem, i am assuming they are standard halogen headlights but as he only got it recently i will check them first, i know he has 2 sets of...

Hi Guys

My son brought a 2006 Toyota Hilux Ute (that was the first problem) and then he wants to install two spotlights (second problem) because the wiring is negative switched which has me...

DIY thread on wheel bearing is just what i am after, mine need adjusting...thanks MudRunner

Well bugger me, mine was stuffed last time i did an oil change so i used an old copper washer from my plumbing box of spares...no wonder it leaks!

Inquire at United Fuel Injection up the great eastern hwy in Redcliffe, i think they might only specialize in Turbo's, not sure, but it won't hurt to ask maybe they can recommend someone if they...

Well guys i checked the lights and they were good, found some wiring done by the people who installed my Ironman roo bar a bit suspect and replaced that and then decided to replace all their wiring...