I'm not a car doctor but preparation for a higher clearance rear bar I performed a Rear Quateroscopy as high as l could go.
I covered the area with black Sikaflex 227.
20220409_135251.jpg
20220408_182442.jpg
20220415_191748.jpg
I'm not a car doctor but preparation for a higher clearance rear bar I performed a Rear Quateroscopy as high as l could go.
I covered the area with black Sikaflex 227.
20220409_135251.jpg
20220408_182442.jpg
20220415_191748.jpg
BrazilianY60 (13th June 2023), Cremulator (12th June 2023), MB (12th June 2023), mudnut (12th June 2023), mudski (13th June 2023), Plasnart (12th June 2023), Touses (12th June 2023)
Not a doctor? You could bloody eat off those boots! Do you have an actual work pair and then a pair for when you just wanna take photos? Nice work. Assuming the rear bar will.be produced in house also? How did you install the weepers to help with water ingress?
Sent from my SM-G988B using Tapatalk
I got red dust in my veins.
Check out My Rig here: Broken
Pics of Forum trips I've Been on:
Pizza at AB's - 2012 Knockwood - 2013 Krissos Place Australia Day - 2015 Pizza at AB's - March 2015 Pizza at AB's - May 2015 Dargo - 2015 Newnes - 2016
WARNING: Towballs used for recoveries can, and do kill people and damage property.
Trolatron (12th June 2023)
[QUOTE=rusty_nail;839910]Not a doctor? You could bloody eat off those boots! Do you have an actual work pair and then a pair for when you just wanna take photos? Nice work. Assuming the rear bar will.be produced in house also? How did you install the weepers to help with water ingress?]
Haha yes Nic id only had them boots about a week. I have no idea why but there was already a thick 40mm plastic tube running up inside the old quatre panel which goes right up to the nearly the window with all the wires running inside it. I sealed up the opening best l could and if any water did get in there it would have to be window deep to get inside the car. Rear bar pics coming up next.
rusty_nail (12th June 2023)
Ah, here is our old friend bptrick posting a link in the full stop at the end of that garbled mess.
growler2058 (13th June 2023)
First time I see a quarter chop on a GU. All the ones I´ve seen so far are on GQs.
1997 Blue Nissan Patrol Y60 blacktop TD42 - Honey Badger (build thread)
2006 White Nissan Patrol Y61 TB45 - G-Unicorn (build thread)
1997 Red Suzuki Samurai Canvas Top SJ413 - Tatui
2005 White Toyota Landcruiser FZJ105 - Stormtrooper
growler2058 (13th June 2023)
1997 Blue Nissan Patrol Y60 blacktop TD42 - Honey Badger (build thread)
2006 White Nissan Patrol Y61 TB45 - G-Unicorn (build thread)
1997 Red Suzuki Samurai Canvas Top SJ413 - Tatui
2005 White Toyota Landcruiser FZJ105 - Stormtrooper
Most people have a single flat bracket onto the front body mount bracket but l like to go overkill.
20230613_085626.jpg20230613_085717.jpg20230613_085658.jpg
BrazilianY60 (13th June 2023), Cremulator (13th June 2023), MB (14th June 2023)
Cremulator (13th June 2023), Trolatron (13th June 2023)
Well done mate. Top notch work done. I widh my welding was neat like that.
Last edited by mudski; 13th September 2023 at 07:43 AM.
Trolatron (13th June 2023)
this is how far the rear bar has progressed so far. I still have to finish the swing arms and decide how I want them set up.
I will get it powder coated when its finished, haven't decided to go black or white yet.
20220414_182413.jpg
20220422_183910.jpg
20220423_152425.jpg
20220424_183849.jpg
20220429_112902.jpg
20220429_112931.jpg
20220503_120551.jpg
20220430_175214.jpg
20220430_144641.jpg
20220510_112044.jpg
20220528_171647.jpg
BrazilianY60 (13th June 2023), Cremulator (13th June 2023), MB (14th June 2023), mudski (13th September 2023), Plasnart (14th June 2023)