-
30th March 2022, 11:07 PM
#711
Patrol Guru
Originally Posted by
MB
Fark, that made no sense apologies....
Quote of the year from @MB about @MB!
-
The Following 6 Users Say Thank You to Cremulator For This Useful Post:
BrazilianY60 (27th April 2023), growler2058 (31st March 2022), MB (1st April 2022), mudski (31st March 2022), Plasnart (31st March 2022), Rossco (31st March 2022)
-
30th March 2022 11:07 PM
# ADS
Circuit advertisement
-
31st March 2022, 05:53 AM
#712
SPAMINATOR
Originally Posted by
MB
Fark, that made no sense apologies Mark Mate, please do put the hard yards in prepping your steel variants by way of taking them back to basics….coatings be gone for full carbon kinky bondages
Sent from my iPhone using Tapatalk
Kenoath! Glad I'm not the only one. I got vertigo trying to read that hahaha
IF YA DONT GET STUCK YA AINT TRYIN HARD ENOUGH........OR YA TOOK THE CHICKEN TRACK
WARNING: TOWBALLS USED WITH SNATCHSTRAPS DO KILL!!
-
The Following 3 Users Say Thank You to growler2058 For This Useful Post:
MB (1st April 2022), mudski (31st March 2022), Plasnart (31st March 2022)
-
31st March 2022, 06:46 AM
#713
The master farter
Originally Posted by
MB
Fark, that made no sense apologies Mark Mate, please do put the hard yards in prepping your steel variants by way of taking them back to basics….coatings be gone for full carbon kinky bondages
Sent from my iPhone using Tapatalk
Ah yeah I was warned about that. I'll be prepping the welded sections for sure.
Just gotta fix my drill press before I continue.
-
The Following User Says Thank You to mudski For This Useful Post:
-
31st March 2022, 06:53 AM
#714
Patrol Freak
Mark, if you're going to put a 2nd piece of angle iron down inside that extension piece, it might be worth cutting a 5-6mm slot on other side so you can weld it to the hub as well.
John
2001 GUII TI 4500 - Now converted to TD42T auto with Nomad valve body
-
The Following User Says Thank You to jff45 For This Useful Post:
-
31st March 2022, 08:09 AM
#715
Moderator
Your front pulley looks like a taper with a left hand thread nut. Clean both tapers and give it a tap when it's back on and tighten the nut. Do you have the nut? If not it should be relatively easy to find one at a specialist bolt or tool store.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
The Following User Says Thank You to MudRunnerTD For This Useful Post:
Mickhead (2nd April 2022)
-
31st March 2022, 09:20 AM
#716
Patrol Freak
The only thing I got out of all that is that MB has been sniffing something. ?????????????
-
-
31st March 2022, 10:00 AM
#717
just clean up the shaft and pulley 680 locktite I did this years ago still going think its a left hand thread so mine has no nut still goes
-
-
31st March 2022, 10:29 AM
#718
The master farter
Originally Posted by
jff45
Mark, if you're going to put a 2nd piece of angle iron down inside that extension piece, it might be worth cutting a 5-6mm slot on other side so you can weld it to the hub as well.
Yeah the first one is welded to the hub, then I found another piece of angle. I've only spot welded the RHS in, I'll either grind them out and weld the angle in properly or do it your way.
-
-
31st March 2022, 11:42 AM
#719
The master farter
Originally Posted by
MudRunnerTD
Your front pulley looks like a taper with a left hand thread nut. Clean both tapers and give it a tap when it's back on and tighten the nut. Do you have the nut? If not it should be relatively easy to find one at a specialist bolt or tool store.
Yeah the nut is long gone, had the thing for maybe 15years and the pulley has never slipped too. I rang a few bolt and tool mobs locally and no one is willing to help. I'll just weld it on.
-
-
31st March 2022, 08:21 PM
#720
Moderator
Originally Posted by
mudski
Yeah the nut is long gone, had the thing for maybe 15years and the pulley has never slipped too. I rang a few bolt and tool mobs locally and no one is willing to help. I'll just weld it on.
Just give both surfaces a clean and a rub with scotchbrite or something like an 800 grit. Then clean. Then place the pull on and give it a couple taps with a rubber mallet. If you have an oversize deep socket plate it over the shaft and hit the pulley on using the socket as a 360d press. I'd be very surprised 8f you couldn't get that left hand thread Nut from an All tools or Sydney tools to be honest mate. Maybe not a shelf item but they'd be able to get it in for you. Go in and flip the lid on one of the floor stock drill presses on display. Evolution has not really arrived yet mate. They will likely be the same.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-