-
30th January 2016, 06:10 PM
#1
Patrol God
RB30 EFI Conversion
This thread is specifically for those who have, or wish to convert their RB30S carby to an EFI set up.
Last edited by NissanGQ4.2; 30th January 2016 at 06:09 PM.
My advice is: not to follow my advice.
-
The Following User Says Thank You to mudnut For This Useful Post:
dom14 (1st February 2016)
-
30th January 2016 06:10 PM
# ADS
Circuit advertisement
-
30th January 2016, 06:12 PM
#2
Rb30 efi conversion
slow internet warning!
for those who have forgone carburetion:
You'll need these components for EFI:
Map of ECCS (advanced technology at the time)
A chart of the inputs and outputs of the control unit.
fuel system. this is an r31 skyline diagram
very simplified air flow diagram. F.I.C.D stands for Fast Idle Compensating Device, it's what kicks in when the AC is turned on, to compensate for the extra load. the air regulator is like a cold start valve, it allows extra air to be put in to raise the idle. some people refer to it as the "electronic choke" but the control unit adds more fuel, the air regulator just adds more air for idle speed (more air past the closed throttle body). it has a bit of influence over the air flow meter too
The crank angle sensor (CAS) and air flow meter (AFM) aren't bulletproof parts. if the engine just refuses to play nice, these two can be the culprit. CAS lives inside the distributor
the all-powerful AFM
more stuff, I adjust throttle valve switches (throttle position sensors) by taking off the connector, loosening the adjustment screws, putting a multimeter set to resistance across the top two pins, and setting it so when the throttle is open slightly the resistance changes. (this is for manuals, automatics have about 6 positions of resistance so need a more complicated adjustment)
stuff
more stuff, oxygen sensor, if your car is fine enough but is just running rich and using too much fuel, pull this guy out, he might be fouled or just worn out. you can't clean any carbon off these, they always need replacing ~$110 bursons retail
injector control
timing control
idle speed control
fuel pump control
basic diagnostic chart for driveability
expanded
another chart
startability
self diagnosis. early self-diagnostic technology, useful, but it's not absolute gospel. can be handy for AFM and CAS codes
how to do it
i've got more from this book, i'll have to sort through it
-
The Following 6 Users Say Thank You to pat in a troll For This Useful Post:
dom14 (10th July 2015), gqsurf (20th May 2016), justy (23rd September 2017), mudnut (4th July 2015), Patrol'n (4th January 2016), Throbbinhood (1st February 2016)
-
16th November 2018, 02:45 PM
#3
Patrol God
With regard to bolting on a turbo and engine compression, I talked to the local Dyno guy.
For a low boost engine, all that should be needed is low comp turbo pistons (concave or spoon crown) and a turbo compatible camshaft.
As the RB30 bottom end is strong, then the original rods should be ok. Using thicker head gaskets is not a good option.
My advice is: not to follow my advice.
-
-
19th July 2020, 01:30 AM
#4
simple wiring suggestion for using vl loom
-
The Following User Says Thank You to Mrbil For This Useful Post:
-
19th July 2020, 01:33 AM
#5
on the vl loom there will be a 4 pin plug bellow the manifold near the bat. connect the 2 orange wires directly to the +12V side of bat. this will provide constant power to wire #1 in picture.
-
The Following User Says Thank You to Mrbil For This Useful Post:
-
19th July 2020, 01:36 AM
#6
if converting from a rb30s settup a new accelerator cable will be needed also.
-
The Following User Says Thank You to Mrbil For This Useful Post:
-
16th August 2021, 03:06 PM
#7
Can you please contact me ASAP 0455435952
-
-
16th August 2021, 04:13 PM
#8
Patrol God
Whats going on? You'll need someone who has done the conversion. I only started this thread to get as much info in in the one place, for those who need it.
-
-
16th August 2021, 04:27 PM
#9
Patrol God
Originally Posted by
Gqpatrol2021
Can you please contact me ASAP 0455435952
Try starting a new thread and ask for help, that way.
-
The Following User Says Thank You to mudnut For This Useful Post:
mudski (17th August 2021)
-
16th October 2021, 11:12 PM
#10
Patrol God
http://www.nissanpatrol.com.au/forum...-r31-loom-help
For those having trouble getting the injectors working.
My advice is: not to follow my advice.
-