-
24th March 2020, 07:07 AM
#451
The master farter
You should be able to remove the lower housing of the fridge John. I would then make up some sort of brace inside the housing so you can screw bolts into it for a better permanent mounting option. That front strap is already pulling away at the mount point and you've only just put it in. Its only going to weaken in time and make it worse.
Last edited by mudski; 24th March 2020 at 12:44 PM.
-
The Following User Says Thank You to mudski For This Useful Post:
jay see (24th March 2020)
-
24th March 2020 07:07 AM
# ADS
Circuit advertisement
-
24th March 2020, 08:48 AM
#452
Legendary
Yeah, was thinking of making up another plate this time rectangle to over the whole bottom of the fridge and a smaller one to set inside the bottom cover.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
24th March 2020, 08:52 AM
#453
Hey what's the fridge like for an armrest? Is it too high, too long or perfect???
-
-
24th March 2020, 10:58 AM
#454
Legendary
Originally Posted by
10G
Hey what's the fridge like for an armrest? Is it too high, too long or perfect???
Perfect hight, but is quite long. I've pushed it forward as much as possible so I can still grab 1st (auto). That makes it just about flush with the rear of the front seats.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
25th March 2020, 09:11 PM
#455
Legendary
Took the fridge out to see how I could bolt it down. The bottom section is in two parts. One is about 1/3, the front section where the cable inputs are. The rear section is sealed to the main body along the sides and around the rear. It also has 4 screws along the red line. Taking them out doesn't do anything to the rear section.
Another way could be with a couple of L shape brackets, one on each corner at the rear, only concern there is if I use a self tapping screw that's about 15mm long will I hit anything on the inside. I didn't think I would. There would have to be at least that much clearence around the unit.
The front I can easily screw through the cover into the plate.
Any other thoughts..
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
25th March 2020, 09:20 PM
#456
The master farter
Whats under the rubber feet I can see to the right of the pic? I would assume there is a screw under this. If there is, maybe use this screw hole as a mounting point?
-
The Following User Says Thank You to mudski For This Useful Post:
jay see (25th March 2020)
-
25th March 2020, 09:45 PM
#457
Legendary
Originally Posted by
mudski
Whats under the rubber feet I can see to the right of the pic? I would assume there is a screw under this. If there is, maybe use this screw hole as a mounting point?
That was the first place I looked when I took it out of the box. Nothing, peeled back the rubber and nothing.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
26th March 2020, 07:22 AM
#458
The master farter
Other option is to make a mounting plate for the outside of the case, which can be screwed into the part of the casing where you can do so and then Sikaflex the front section of the plate to the base. Or drill right through the insulated fridge section and bolt it down onto a plate. Then just silicone over the bolts on the inside. Use stainless bolts though.
-
-
26th March 2020, 10:14 AM
#459
Keen to see what this looks like when it's done. I've started looking for an arm rest for my left arm, a fridge may be the answer???????
-
The Following User Says Thank You to 10G For This Useful Post:
jay see (27th March 2020)
-
27th March 2020, 09:32 PM
#460
Legendary
-
The Following 3 Users Say Thank You to jay see For This Useful Post:
mudnut (28th March 2020), mudski (27th March 2020), rusty_nail (28th March 2020)