Gu seat belt drama

[BillsGU]

Took Bills GU's advice and got some replacement ones from seat safe, went off road over the weekend in and out of the truck all day and they had retracted every time.
Was getting so fed up with the OEM's, these work a treat, took a bit of fitting as Bill said but once one was done the other was so easy.
Thanks Bill, Macca

No worries Macca. If anything - mine are a bit sensitve. If the car is a bit out of level when putting on the belt it sometimes does not pull out. Not sure if there is an adjustment for that. I'll give them a call and ask.

BTW - mine are grey and they suit fine, especially as I have replaced both front ones. You may see a difference if you only replace one.

[macca]

No worries Macca. If anything - mine are a bit sensitve. If the car is a bit out of level when putting on the belt it sometimes does not pull out. Not sure if there is an adjustment for that. I'll give them a call and ask.

Same here, did find they came out once level and moving which suprised me.
That was the main problem I had installing them - getting the belt to come out.
Put retractor in the vice and it worked. Figured it was level/movement problem.
Put them in the ute and bolted firm.... perfect.
Thanks again Macca

[TimE]

Maybe this vid might help explain what is happening

[threedogs]

Thats why I have proper clips to hold seatbelt open when 4x4ing, I can get in and out fast if need be .

[Anaurath]

Hi Guys...

Today I tried to register my GU in WA. Still had the SA plates...

Do you know the reason why they do not let me pass the inspection?

Tic, Tac, Tic, Tac,....

Yes, the seatbelts...

Fortunately I've been able to check that all your comments and solutions are aligned with the ones I've found over the Net.

I will try to get the kit sold by Nissan tomorrow, but also work it out a deep clean to the belts and a apply a good layer of Nulon Ezy Glide to the retractile mechanism.

Hopefully it works... I have another inspection next week!!!

[my third 256]

Hi Guys...

Today I tried to register my GU in WA. Still had the SA plates...

Do you know the reason why they do not let me pass the inspection?

Tic, Tac, Tic, Tac,....

Yes, the seatbelts...

Fortunately I've been able to check that all your comments and solutions are aligned with the ones I've found over the Net.

I will try to get the kit sold by Nissan tomorrow, but also work it out a deep clean to the belts and a apply a good layer of Nulon Ezy Glide to the retractile mechanism.

Hopefully it works... I have another inspection next week!!!

speak to the mob that sold it to you and tell them its unroadworthy what they going to do about it

[4by]

I found that the slot where the seatbelt went through the top fixture was tight. Cut a strip of sandpaper and inserted between the belt and fixture. Sandpapered and bingo Seatbelt retracted easily.
It builds up grease from hands.
Try the above A cheap Fix.
Belt Needs to be cleaned as well

I took Bob advise. Cleaned the belt and bit of sandpaper helped them work better for now. I'll give em another clean but they retract better so I'm happy.

[threedogs]

Bob can you take too much off ?

[4by]

It's not easy to fit a piece of sandpaper in between the top fixture, so I don't think you will be sanding for a long time. The more you take off the bigger the gap and easier for the belt to slide through. Just sand for a few minutes and test it until it slides through easily. I also cleaned the belt as it was dirty which you might need to do.

[Bob]

Bob can you take too much off ?

As long as you make the Fitting smooth it does not matter how much you sand off (Within Reason)
Just use a Fine Sandpaper to finish off as the Belt needs a smooth Surface to slide through.
Wash the Belt with Dishwashing Liquid in a warm water solution