OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: nissannewby

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    19
    Views
    553

    The performance curves are hard to find for td42...

    The performance curves are hard to find for td42 specific alternators. Maybe a very good auto electrc company could get them.

    Your observations are correct with the cable from the alternator ...
  2. Replies
    4
    Views
    258

    Part of the filler cap. Have seen it quite a few...

    Part of the filler cap. Have seen it quite a few times.
  3. Replies
    24
    Views
    988

    No you are right I was confused. It gets a little...

    No you are right I was confused. It gets a little hazy sometimes. I deal with tube and pipe at work and they are measured differently. I was right about the schedule rating though.

    So yes your...
  4. Replies
    24
    Views
    988

    Also check if their bars are adr approved. Airbag...

    Also check if their bars are adr approved. Airbag compliant etc etc. These details are what insurers will be looking at if you were to run into someone or something. No compliance no insurance.
    ...
  5. Replies
    24
    Views
    988

    40NB (40mm nominal bore) with a 3.25mm wall will...

    40NB (40mm nominal bore) with a 3.25mm wall will be 46.5mm OD ��. Nominal Bore tube will normal have a schedule rating and this is what determines the wall thickness.

    So if you want a 50ish mm OD...
  6. Replies
    15,344
    Views
    1,651,881

    Sticky: A full bowl of fruit loops for breakfast.

    A full bowl of fruit loops for breakfast.
  7. **Disclaimer** No bread makers were harmed during...

    **Disclaimer** No bread makers were harmed during this event.....
  8. Replies
    2
    Views
    281

    You can get the solenoid out without moving that...

    You can get the solenoid out without moving that screw. You can just get the right size spanner in there. You can also normally get to the 8mm nut without to much worry as well.
  9. Replies
    5,080
    Views
    536,416

    Depending on your roof style clamps might be the...

    Depending on your roof style clamps might be the only option. Some models do have the rails bolt onto them that run front to back but if they arent there fron factory then it won't leave any other...
  10. All of this is all good and well. And it's great...

    All of this is all good and well. And it's great that the outcome will be a new crate motor. But are you 100% the motor that was put in for the previous owner was new? It could have been a second...
  11. Replies
    3
    Views
    222

    In Qld mate. It's near the top of Cunningham's...

    In Qld mate. It's near the top of Cunningham's gap. It is an awesome family camping spot with some good all round 4x4 tracks. Nice creek for swimming. The 2 extreme hills are a good bit of fun to.
  12. Replies
    13
    Views
    489

    Yeah you could attempt to clean it up with some...

    Yeah you could attempt to clean it up with some wet n dry. I would be measuring with a mic if possible. Then just pay close attention to sealing it all up when re assembling to hopefully prevent...
  13. Replies
    13
    Views
    489

    Should only really use the LMM in the CV. Use...

    Should only really use the LMM in the CV. Use your other red grease for everything else.
  14. Replies
    13
    Views
    489

    So the specs say the bearing ID should be 41.275...

    So the specs say the bearing ID should be 41.275 so that one is under by quite a bit really.

    Yeah it could have been worn or possibly adjustment has caused it. It could have also been the...
  15. Replies
    13
    Views
    489

    What is the part number of the bearing?

    What is the part number of the bearing?
  16. Replies
    13
    Views
    489

    I would say heat. It looks as though the inside...

    I would say heat. It looks as though the inside of the smaller bearing has been spinning on the shaft. It may have gotten super hot as the inner race was creating friction on the stub and then it has...
  17. They actually make a 18v coffee machine....not...

    They actually make a 18v coffee machine....not quite a sandwich press but might interest some for super remote coffee time.
  18. Do a burnout then put the fronts on the rear and...

    Do a burnout then put the fronts on the rear and do another burnout. All fixed lol. Make sure the surface is flat prior to doing said burnout.
  19. Poll: The mrs isn't super keen on coming as she will...

    The mrs isn't super keen on coming as she will have just gone back to work after maternity leave. It will be just me and a small possibility of my 2 oldest boys. Although if I have to work then I...
  20. Poll: 🤬🤬😔😩 This is the weekend of the Melbourne 4x4...

    🤬🤬😔😩 This is the weekend of the Melbourne 4x4 show. I will possibly be down there working at the show. I will need to confirm this before I am able to confirm Licola. Bummed I have wanted to do this...
  21. Replies
    547
    Views
    57,038

    Take the inner guard off and just unplug it while...

    Take the inner guard off and just unplug it while its in the up position.
  22. Replies
    1,820
    Views
    320,320

    MB sounds like you were the quiet hero. As dire...

    MB sounds like you were the quiet hero. As dire as the situation was keeping a cool head helps prevent the situation getting out of control. Also keeps the driver in a slightly calmer state. Not fun...
  23. Replies
    119
    Views
    4,363

    It will be a pu with some type of silica content...

    It will be a pu with some type of silica content similar to that used in the adult industry. I will do some research and see if I can find a material. It may even have some kind of vinyl in it. PU is...
  24. Replies
    119
    Views
    4,363

    The plastic is cheap and the end fittings are...

    The plastic is cheap and the end fittings are just some steal tube and bar. A unit could be made for $50-$100.
  25. Replies
    119
    Views
    4,363

    How many do you want?

    How many do you want?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4