Mark, I have this conversion and I am now sitting in the sweet spot for max economy at 110klm/hr at 1750rpm.Unlike the 85% reduction gears that howl all day in low range the machine finish is...
Type: Posts; User: PeeBee
Mark, I have this conversion and I am now sitting in the sweet spot for max economy at 110klm/hr at 1750rpm.Unlike the 85% reduction gears that howl all day in low range the machine finish is...
Its a mounting bracket for a Codan HF radio. Its mostly behind the headrest, but i am going to chamfer the stiffeners to take away the sharp corner - funny what you dont see when you are making it....
Fabricated another custom bracket to mount the Codan HF radio, time consuming and converting ideas into reality - came out well, mounted above the SS water tank behind the rear seat...
Got the rear pod wired 95% today, power to lights, inverter, DCDC, fridge, exhaust fans on thermostats, just need to do the penetration to get the charge cable into the pod - maybe tomorrow. Lights...
I think this refers to the diaphragm valve inside the pump so it sucks in liquid and the valve closes then the diaphragm discharges against the closed seal, pretty normal, there will be a flow arrow...
So you think the issue happened before you installed the 20mm body blocks ? Is there a witness mark on the bonnet or the barrel? Where was it rubbing? Are you sure its not a manufacturing leak? Can...
The diaphragm pump has a poor suction capability, which is why they only rate the discharge head. You will do better lowering the inlet of the pump to the same level as the tank outlet, then it...
The kits are optioned up like crazy, simply select which one you want, some are twice the complexity. Its all 4mm pipe and the only weakness V the strength is there are 3 mounts , so I have purchased...
Thanks for reminding me Darren, I have one of those also, bugger, would have been done in 15 minutes. Those tom thumb units are a bitch.
Looks like I am up for a new or remodelled interchiller tank. The location of the tank outlet was deliberately put at 1/3 off the bottom of the tank to reduce any drawdown of crap into the pump...
Looks great, very neat, well done.
Interchiller wiring finally resolved, bigger cables, big relay, runs beautifully, see if it delivers, swapping out the water or glycol this arvo.
The heat exchanger is on the rear of the fridge, the jackets provide the insulation to the sides and top.
Sorted the Interchiller pump out today, conductor size and volt drop. Rigged up a 200a/hr lithium and short heavy cables, fired the pump up, guaranteed 40lpm by the flowmeter thru the system, happy...
Its the price we pay for the dickheads who put the poor money managers in charge of the bank. Our 15 acres in Gippsland costs 4k in rates for a cow paddock without any physical services and a dirt...
Where did you source these bins? I ran these in my original susyem and they are great, but local Bunnings stopped carrying them, and everything else apart from some $0 tubs in a single size work.
Who is this directed at?
Another good optimisation, thanks.
Thanks Mark, yes that will work also, sealing it up has some issues if the welds crack or I dont do a good job on the checkerplate. I dont need the weight as you mention. Back at the computer again...
No just the packing, all loose, tacked them together today, took 20 mins, after spending 7 hrs fighting with the interchiller pump, that has now been 100% confirmed as dead - pumped at 40lpm with a...
2 hrs transferring 4l of hydraulic fluid into the hydraulic winch tank, holy shit that pumping is hard work under the car. reconfigured the interchiller pump circuit back to standard, still a few...
Yes it's what sold me, I look like I can stack a large and 2 stalls on top of each other as two large are too tight it looks. Anyway will see, they have some good options, as do the expeditions
Procrastinating about the format of the rear pod, bit the bullet today and bought the starter pack from TRED, which has a 55L and 2 x 27L units. Combo seemed to work a bit better than the Expedition...
Slider kit finally arrived after 6 weeks - they must have been busy. Looks a good kit, precision made, all notched, just need to weld then paint, happy days. Going to plate top and bottom using the...
You can get these clips on ebay or via Patrol a Part, not expensive at all.