OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Funny you say this, I have been trawling for some...

    Funny you say this, I have been trawling for some stats on just this but not much love.

    4BYE4 is on the money too.
  2. Had to be at least one fool.

    Had to be at least one fool.
  3. The main issue with the ZD30's is the weakish...

    The main issue with the ZD30's is the weakish pistons. Rest of the motors are quite strong and the factory turbo can handle a lot of boost (30+PSI).
    The pistons would either blow through (hole in...
  4. Depends of the pistons used (rebuilt donk for...

    Depends of the pistons used (rebuilt donk for grunt likely to have non-stock pistons) and the cylinder volume.

    If you wan't a reliable Outbacker to carry spares, loose the RB30 and run a TB42 or...
  5. A small battery to provide exciter power to get...

    A small battery to provide exciter power to get the field energised, after running and producing power then it could be run standalone but regulation will be shit. Use a battery on it (just a little...
  6. I am assuming an RB30 looking at the manifold and...

    I am assuming an RB30 looking at the manifold and your signature.....?


    Anyway, RB30 has a pretty strong bottom end, heads are ordinary but workable but even better, Stronger guts are not hard to...
  7. Replies
    10
    Views
    3,460

    Dump pipe off and check shaft play. If it...

    Dump pipe off and check shaft play. If it wobbles, she is farked.

    P.S If it is farked, you are putting metal shavings into the motor.
  8. The alternator doesn't settle @ 13.8V, the is the...

    The alternator doesn't settle @ 13.8V, the is the resting voltage of a healthy battery, not its charge.
    I will say it again, sense wire should be a the Batt+ terminal, not on a amplifier or other...
  9. The "Sense" wire is designed to be connected...

    The "Sense" wire is designed to be connected directly to the battery or as close as possible. The reasoning for it is to ensure the correct voltage is at the battery overcoming any volt-drop (Vd) and...
  10. Evil creatures for lazy people. Strip, solder and...

    Evil creatures for lazy people. Strip, solder and tape/heatshrink.
  11. Replies
    12
    Views
    3,591

    Dude, I don't even know what thread or where it...

    Dude, I don't even know what thread or where it is, there are serious way too many forums to keep track of on the site...
  12. Replies
    25
    Views
    3,437

    The factory suckers are in tighter than a nun's...

    The factory suckers are in tighter than a nun's nasty. We used a lot of heat, bearing pullers and big hammers (use one a dolly to put mass behind bar, use other smaller hammer to smack the sucker) to...
  13. Replies
    34
    Views
    18,415

    Might pay to look at my Turbo & Exhaust wrapping...

    Might pay to look at my Turbo & Exhaust wrapping thread.
  14. Replies
    14
    Views
    15,623

    I don't have a CRD nor worked on one. I have...

    I don't have a CRD nor worked on one. I have noted other in past finding total external boost control can make limp-mode hell along with possible de-rating power. This would be best answered by those...
  15. As I say to any of my business clients, if you...

    As I say to any of my business clients, if you use the machine as a tool and it going down will impact your business, then leave it alone. If it is running Windows 7 or 8.1 and working fine, leave it...
Results 1 to 15 of 44
Page 1 of 3 1 2 3