ZD30 tinking noise

Hey all,

I have a metallic 'tinking' noise coming from the engine, it's also evident at the rear from (through) the exhaust?

I got a stethoscope onto it and seem to have pin pointed the location, it's at the engine near the turbo inlet (from the exhaust manifold).

Some searching round the site suggests a possible loose exhaust manifold gasket, but I'm not sure if that would be the case? Just got my turbo rebuilt and it's refitted fine, the noise was evident before the turbo was rebuilt. The noise also seems worse under acceleration and when cold?

Any suggestions welcome!

Could be a warped exhaust manifold, common problem.
Have a search see what you come up with

I've got a high pitched squeal in mine somewhere around the turbo/manifold.

Possibly a damaged valve seat?
Nothing been dropped into the inlet manifold?

Check the security of the heat shield attached to the turbo.

Hey all, so I have had the turbo rebuilt and I reinstalled same with all new gaskets and nuts, torqued to spec as per manual supplied by this magnificent site! (thanks!) Nothing was dropped in jono 6974, i made sure to be careful on the install. Bills gu, i have checked the shield and customised same for my temperature probe, so all seems ok.

robewott - perhaps its a polished bearing in the turbo, or pitted bearing, get a stethoscope and see exactly where it is coming from, use a hose with a barb end (from bunnings irrigation section, use a barb end with any kind of hose the fits) and see where exactly where the noise eminates from.

Is this tinking or ticking noise in sync with the engine revs or with the turbo spooling up ??? This will give away whether it's the turbo or something on / in the block itself.

any luck with this yet ??

Hey all, the tinking is in time with the engine revving up, but doesn't seem to be as fast as the revs, if that makes sense? Turbo is fine by the sound and look of it. Haven't had the time to pull it all down again to check the gasket on the exhaust manifold, quite frankly its been off the rd for 3 weeks with the turbo out, I put it back together and don' like the idea of having to pull it down again! Especially that dang heat shield!

The noise disappears when the engine is warm, so I'm def thinking the gasket...

Grab a bit of garden hose, when the car is cold and making the noise put one end to your ear and run the other end around the gasket areas you will clearly hear where it is leaking.

We had an exhaust shop in the family for 20years and that was how we used to pin point leaks.

Quote:

---

Originally Posted by Lexx

Hey all, so I have had the turbo rebuilt and I reinstalled same with all new gaskets and nuts, torqued to spec as per manual supplied by this magnificent site! (thanks!) Nothing was dropped in jono 6974, i made sure to be careful on the install. Bills gu, i have checked the shield and customised same for my temperature probe, so all seems ok.

robewott - perhaps its a polished bearing in the turbo, or pitted bearing, get a stethoscope and see exactly where it is coming from, use a hose with a barb end (from bunnings irrigation section, use a barb end with any kind of hose the fits) and see where exactly where the noise eminates from.

---

It's only there when the engine is cold. It sounds like the exhaust manifold.

Could be a slight blow from an exhaust gasket that seals when engine warms up.

apart from the the head gasket on the exhaust side, what other gaskets will i need after pulling off the manifold? Can the turbo unit be pulled to one side while the ex gasket is replaced?

Hi guys, unfortunately I have been unable to reply for some time. I have sorted this issue out, it was the exhaust manifold gasket. It was THE ONLY one I didn't do when I rebuilt the turbo.... pulling it all down again and paying for new gaskets... slightly annoying.... cutting hands on heat shield... again... totally enfuriating!

Cheers all to the good advice :)

Was looking at the Necro thread digging. Nearly a year... LOL

At least you sorted it.

Quote:

---

Originally Posted by Lexx

Hi guys, unfortunately I have been unable to reply for some time. I have sorted this issue out, it was the exhaust manifold gasket. It was THE ONLY one I didn't do when I rebuilt the turbo.... pulling it all down again and paying for new gaskets... slightly annoying.... cutting hands on heat shield... again... totally enfuriating!

Cheers all to the good advice :)

---

Hopefully you modified the heat shield for future removal etc..
I found mine comes off much easier with actuator taken off..

But issue found. Nice one.

BIGGUWESTY - Stop reminding me of things AFTER I have done them! Although, I found I can get the shield on if I am patient and gentle, which isn't often lol.

LOSTBENJI - I'm like a good woman, never forget and pounce years after the fact!

Quote:

---

Originally Posted by Lexx

Hi guys, unfortunately I have been unable to reply for some time. I have sorted this issue out, it was the exhaust manifold gasket. It was THE ONLY one I didn't do when I rebuilt the turbo.... pulling it all down again and paying for new gaskets... slightly annoying.... cutting hands on heat shield... again... totally enfuriating!

Cheers all to the good advice :)

---

and what have we learnt here, I left the heat shield off the turbo, well somebody did.
Made it easier to fit the beanie anywaylol, Good to hear its sorted

Quote:

---

Originally Posted by bigguwesty

Hopefully you modified the heat shield for future removal etc..
I found mine comes off much easier with actuator taken off..

---

Even easier when in the scrap pile.

Quote:

---

Originally Posted by Lexx

LOSTBENJI - I'm like a good woman, never forget and pounce years after the fact!

---

ROFLMAO @ the FACT

Quote:

---

Originally Posted by threedogs

and what have we learnt here, I left the heat shield off the turbo, well somebody did.
Made it easier to fit the beanie anywaylol, Good to hear its sorted

---

Yerp, beanie wins hands down.

Quote:

---

Originally Posted by LostBenji

Even easier when in the scrap pile.

ROFLMAO @ the FACT


Yerp, beanie wins hands down.

---

Yea Bennie will be on soon.. just funds only allow a fee things at a time..

LOL, you're just pissy that I beat you to it. Under 100 bucks for beanie and wrap, not too costly.