Printable View
I need to rotate my clutch lever on the winch.
Attachment 51526
I can't seem to get to it from underneath. The plate is bolted to the chassis.
Attachment 51527
Do I undo the three bolts that you see at the top of the pic, that will allow me to remove the whole bullbar (TJM). There's another bolt below the bottom one, but they both go into the chassis.
Cheers in advance
Yep remove the whole bar as this makes getting to winch easier. Those bolts should be 22 mm from memory
May as well give it a full service while its out, they are simple but more grease isn't better it just makes it hard to spool
Thanks guys.
Just needed to be sure.
Will have a look at servicing, but winches are all new to me.
Is there a particular grease to use.
Well I managed to get the lever in the right position.
Attachment 52392
Now it wouldn't spool out, works both ways when in the "IN" position.
Where have I gone wrong.
Did you re pack it with grease ? If you put too much grease in it the outer ring that slides over the planetary gears may not be sliding properly and staying in gear. I'm referring to part 19 http://www.warn.com/truck/winches/pdf/900499E1.pdf
No I didn't.Quote:
Originally Posted by megatexture
It was working fine earlier I presume? Did it look ok inside when you had it apart to rotate it ?
Yep.Quote:
Originally Posted by megatexture
It still works just won't spool out by hand so I leave it for next time. Unless someone has any other ideas.
I have noticed with some winches there are only certain positions that the lever can mount up ..... wont work properly in just any position.
Try loosening, and totating slightly to see if this has any affect
Mic
Sorry mate, other than pulling it out for a clean out or tapping it with a hammer while trying to disengage it I don't think there's much to do.
The handle has a off centre pin on the end of it that slides the ring gear off of the inner gears but something must be jamming it preventing this action.
Can you remove the clutch lever and check if the pin hasn't snapped off ? Mines held in with a grub screw.
OK, will have a look and try your thoughts probably on Monday (day off).Quote:
Originally Posted by megatexture
Thanks for your input.
OK. Need to get it working proper.
Spools out but hard to do.
Got it out a apart. Do I just wipe out as much as I can, or wash it out with something?
How much grease is too much.
SCA have marine grease???????
Attachment 53673
Too much grease will make it very sticky and hard to free spool. Many use LMM grease, the black stuff as its not as thick. But It's not waterproof. So if you plan on doing regular servicing it will be o.k. I used Castrol Premium Heavy duty grease, the old APXT in Castrol. I made the mistake of first using the Truck and Farm grease which is super tacky. I couldn't even move the hub. Cleaned it out and then used the Premium Heavy Duty grease, but not too much. Pretty much the same as whats on the gears in your pic. The hub was a little firm to move but still pretty good. So I was happy with that.
Thanks mudski.Quote:
Originally Posted by mudski
What's LLM, sorry. Is the castrol waterproof?
Not planning on serving always only when needed, but I do want to relocate my control box, just not sure where.
Found this in the shed Attachment 53675
What do you think.
Went back to look and its what you use just the old stuff. Haha
That stuff if fine. It says on the top of that tube, formerly known as APXT, which is now called Premium Heavy duty. Lmm is the Black grease, great for this application but not waterproof, thats the only issue with it.Quote:
Originally Posted by jay see
OK. This one is blue!!!Quote:
Originally Posted by mudski
Now I've had it in and out three times and nothing happens, I think I can hear things turning but the drum won't move. The shaft in the pic has 6 flats on the end but the end of the gearbox has a round bush.
Also the gear on that shaft doesn't line up with anything on the end of the gearbox pic 2.
What am I missing.
Attachment 53678
Attachment 53679
Never mind
Dickhead I am.
Winch back in and working, will put it all back together in the morning and go and find a tree to test.
Took a while but now I've learn something new.