Printable View
Has any one mounted a retractable air lead in the back of their patrol wagon?
If so where did you mount and what do you have?
This is the one I'm looking at
http://www.jamecpem.com.au/index.php?p=prod&sid=58.2671
It measure 300x300x150
I was thinking of mounting it in the window frame of the rear of the cab to the grab handle mount.
What does every one think and what can you add?
Regards
Shaun
To be honest I reckon it's just a bulky way to carry the hose you need. I thought about a coil type hose but again I think it is bulkier than the hose I use now. I use a reusable zip tie or you could use Velcro to hold the hose in a loop then I tie it to the cargo barrier in the GQ and happy days.
I don't have a cargo barrier. But I get what your saying.
I'm just trying to make pumping up my tyres as easy as possible and as cool looking as possible. :)
Do you have a on board setup or portable?
If onboard run a line alone the chassis rail from bull bar to rear bar with quick release air fittings, then you only need 2 or so mtrs of hose..
Kallen Westbrook
Owner of
Westy's Accessories
In the process of installing on on board system, with tank and air manifold for later expansions :)
also dont want the fittings on the out side as they will get full of crap. Mud gets everywhere on the out side. lol
Mine is on the outside and no issues here ... when I get back home from my travels, I will post up a pic.
Mic
Both my vehicles have onboard air. Both are pretty much set up as Kallen suggests. One (small bus) with air outlets on the front & rear bumper bars, each with a push on/pull off cover to stop crap getting into them. (Compressor & tank underneath vehicle with airlines along the chassis rails). The other (my Patrol) has the compressor & tank mounted inside the canopy, with an outlet on each side of the canopy, inside. The hose I carry reaches all wheels & as well as under the bonnet. Far less bulky than curly hose or retractable set up.
Cuppa
Use the push in air fittings, then run via a manifold and oneway valve and air stone filters and pressure switch,
as others suggest mount female "nitto" fitting front and rear. Then you only need 3mtr length to reach all 4 wheels.
Curly hose crimps and becomes useless, there is some very flexible hose available these days. Use Nitto instead of the Jaymac
twin barb fitting as you get more air flow, Tank wise along the inside of the LHS of chassis is norm for the smaller tanks
for lockers. Or up under the rear for larger tanks. Dont forget a bleed/Drain screw. Lubricator not required ATS
You can get covers for the fittings eg Door stops fit I think, trim to suit look neat and cheap
Shaun,
You could possibly compromise, and mount a fitting inside the fuel cap area, outside but yet inside, if you are worried about it ....
You can get rubber caps on chain to keep the dirt out to suit most popular plug types.
Kallen Westbrook
Owner of
Westy's Accessories
The tank and compressor I'm gonna be mounting in the spare spare on one of the sides from my drawers in the back.
I'm also gonna put the outlet in the back of the drawer aslwell. That way I only need to open the the little door and ill just keep using my arb airline.
Then ill just run another lead to the front and mount a fitting somewhere up there.
This looks the go for a cover
http://www.nissanpatrol.com.au/forum...onnector-Cover
Thanks guys.
Walking stick ends go figure, Shawn you can also buy brass hex nuts to tighten fitting where ever you go through.
only seen 1/2 " bsp, But well worth it to secure the outlet.,Some guys drill and mount front outlet just next to uprights
on bull bar either via an elbow or straight fitting, plus well protected
I love the idea of retractable coil, I need something bigger because I used my on board compressor for work to run my nail guns.
Do you have a link to what you mean to mount the with a nut, as in what kind of nitto are you talking about?Quote:
Originally Posted by threedogs
I've tried three times now to have the arb one mounted and that's a dead end, that fitting don't like to be flush mounted.
Shaun, I like the idea as well - it would be great if you could mount it under a seat or some where else out of the way.
I love this idea, I got my hands On this today Im going to give it an go.
Removable hinge mount means it an be pulled off mount and stored.
http://www.nissanpatrol.com.au/forum...013/06/166.jpg
It makes a whole lot of sense.
I bought this airhose partway down the page
http://www.sidewinder.com.au/page167aaa.html