$50 GQ storage boxes

Hey guys. I thought id share one of my DIY projects. My GQ needed some form of rear storage, having big plastic tubs strapped down in the back to hold all my recovery gear etc was just taking up too much room and all the bumping around of 4wding sees the boxes getting broken all the time. Not to mention the sub box I had in there with 2x12" subs taking up a heap of room!

I didn't want drawers as I need the height in the back for the kids bikes to go in and the potential to run the dickie seats is also handy with 3 kids.

So.....I decided to use the 'wasted' space over the rear wheel arches, by making up a storage compartment that also incorporates a speaker box.

First I stripped out the rear of the GQ.

https://fbcdn-sphotos-d-a.akamaihd.n...42945410_n.jpg
https://fbcdn-sphotos-c-a.akamaihd.n...64662598_n.jpg

I refitted the RH side trim, it is out in this pic to run the wiring needed for the fridge.

Then I had to get the materials needed for the job. I bought....

3 sheets of MDF, 2x 1200x900x12mm thick 1x 600x900x12mm thick, 4 small hinges, 2 pairs of magnetic door catches, 2 handles, some right angle brackets, some screws and liquid nails. All the materials cost $50.25 at my local bunnings.

https://fbcdn-sphotos-b-a.akamaihd.n...88538034_n.jpg
https://fbcdn-sphotos-c-a.akamaihd.n...85003409_n.jpg

I then transferred my plans to the MDF, I was able to make most of the panels required for one side from 1 sheet of MDF, the smaller sheet was needed for the partition and one of the ends.

https://fbcdn-sphotos-f-a.akamaihd.n...49558554_n.jpg

Then I simply cut it all out, planed all the edges and screwed it all together and trial fitted it.

https://fbcdn-sphotos-h-a.akamaihd.n...20772624_n.jpg
https://fbcdn-sphotos-g-a.akamaihd.n...17075472_n.jpg

Then once I was happy with the fit of the main box, I then cut and fitted the end piece that is closest to the front of the car, which matched the profile of the wheel arch, and I made a divider, which also follows the profile of the wheel arch, to separate the storage box section from the speaker box section. Sorry, no pics of this but I can take if you want!

Then I fitted the magnetic door holders to keep the lids closed, the handles (which I now don't like!) and cut the speaker holes for the 6x9 speakers.

https://fbcdn-sphotos-c-a.akamaihd.n...34681132_n.jpg
https://fbcdn-sphotos-f-a.akamaihd.n...73862382_n.jpg

All I need to do now is fit the power sockets once I work out where I want the fridge to go, and carpet the whole lot.

And the boxes dont look really big to look at.....

https://fbcdn-sphotos-f-a.akamaihd.n...24566778_n.jpg

But just in the left one, I have 2 snatch straps, a tree trunk protector, winch controller, recovery blanket, 2 pairs of gloves, tow hitch recovery point, 2 ratchet straps, a couple of cans of various lubes and cleaners, bow shackles, some rags, the jack, jack handle and wheel brace. That leaves the RH side for things like spare oils, parts etc.

Thanks for looking!

Nice work!

Thanks for that. They work well!

Yep, functional and made on a budget. Well done mate!!

Thanks mate. I do everything on a budget!

I like it mate, leaves loads of room to store stuff in the back too!

Look great that MDF stuff hates water. protect it some how?
I like the way you went full height.
Now more ideas ,power outlet , side speakers?????

The MDF does not like water, but thankfully, I dont plan on sinking it! I do need to carpet them though. Since that project was done, Ive added a double power outlet with one outlet for the fridge and the other to charge a torch. It has speakers on the top of the box, so with the back fully loaded we can still hear the music.

Great boxes, the Dev is full of talent , well done.


Sent from the secret chambers of our secret society, on a secret iPhone, with a secret pin code and eye retina scanning from a secret peep hole, just don't tell anyone OK, cos it's secret........

Nice looking boxes mate. i think i may copy them one day:). Maybe you could find some real cheap gas struts from a wreckers so they stay open when your rumaging around in there?

Thanks for the feedback. I have thought about that, but I may gust do a simple magnet setup to hold it open.

Mate get some marine carpet and turf glue and cover them. It really finished the job off and it is easy to do.
If i can do it any one can, you get that warm feeling from the carpet and it looks great.
Nice work.

Nice Box.... 's.. Your setup is thinking outside of the. Well box..


Kallen Westbrook
Owner of
Westy's Accessories

Like to see someone thinking laterally. Great idea !
How about a lockable gun rack/box ?

Cheers

What about hinging them the other way, so when you go 4x4ing and if by chance you get stuck, you can access your recovery items from the outside of your 4x4.
Just remember to un click your sliding window first

Good idea but wouldn't see it as being an issue the way it is.

does anyone know how he attached the boxes to the body of the car?

Quote:

---

Originally Posted by rusty_nail

does anyone know how he attached the boxes to the body of the car?

---

I'm guessing threw on of many of the hold down points in the rear. There an M6 bolt and if you use a counter sunk bolt then it will be flush ontop, slowing draws to pass over it..
You can also use the rear seat belt bolts..

Kallen Westbrook
Owner of
Westy's Accessories

@ Rusty give him a PM ,maybe he used a Rivnut tool which is great for inserting a captive nut up to M10 into sheetmetal
Best of all its neat as and strong

thanks TD, will do.

Some great idea's

nice work. its got me thinking

Great idea

Cool idea might copy that one cheers

Sent from my IQ255 using Motorculture mobile app

Got any pics of it carpeted

Sent from my IQ255 using Motorculture mobile app