A new alternator after mine decided to pack it in.. 😕
Sent from my SM-G925I using Tapatalk
Printable View
A new alternator after mine decided to pack it in.. 😕
Sent from my SM-G925I using Tapatalk
Did you get an upgraded unit, or just replace like for like?Quote:
Originally Posted by sooty_10
$7!!! Once it's covered in weld spatter and crap I'll just bin it and get a new one..
Save my $200 at home..
http://www.nissanpatrol.com.au/forum...015/10/319.jpg
Buy a leather cover for it that will keep it looking new for longer
http://www.ebay.com.au/itm/Leather-W...MAAOSw0vBUlMLA
That's 4 more watches right there. Lol
Just standard 100 Amp hitachi same as what was on it.Quote:
Originally Posted by Bacho86
Sent from my SM-G925I using Tapatalk
I know what you mean I have a heap of skeleton wrist and fob watchesQuote:
Originally Posted by biggqwesty
http://www.ebay.com.au/itm/Vintage-S...-yj2cqu_MzW2Tg
Mine is the factory intercooled, but its the last of series 3, (early 2004) and ive been told it has no ecu, still mechanical injection ect.... can any one confirm?Quote:
Originally Posted by nissannewby
Ok so it seems they do have an ECU but it doesn't control much def not fuel, any one know what they do control?
A bit fancy thereQuote:
Originally Posted by threedogs
Went to buy a drivers side guard of a guy in Mornington for $50 ended up with 2 for $70 both have been on a car but have never had a real coat of paint and are still in the panel black as new. Perfect condition.
20L of penrite oil for $119 from repco ready for the next service!
http://www.nissanpatrol.com.au/forum...015/10/328.jpg
Sent from my iPhone using Tapatalk
Nice Bacho. Curious how come you went for 50 viscosity. Summertime?
Also how did you go with your rear main seal.
Yeh combination of things...I have normally used the 15w-40 but I couldn't get that on special in the 20L drum at the time. Plus penrite specifies that the 15w-50 can also be used when 15w-40 is specified, so we'll see how it goes!Quote:
Originally Posted by Hodge
I'm dropping it off with ATOC to get fixed over the new couple days, so fingers crossed!
Sent from my iPhone using Tapatalk
Another project for the time off.. pick it up tonight
http://www.nissanpatrol.com.au/forum...015/10/331.jpg
I run a 5/40 with no problemsQuote:
Originally Posted by Hodge
i have one almost identical, i notice the butterfly damper on the top of the fire where the flue goes is missing but you can make that up, just a circle of metal with a handle to damp it down and slow the burn. they are a very good heater btwQuote:
Originally Posted by biggqwesty
Yea friend of mine has one inside and it's good..Quote:
Originally Posted by Stropp
Was looking for more an oven but guess I can still make that 😆
Penrite has a new line called "extra 10", you can see it on the label there. Basically with "new technology " all their ratings go up by ten. But as said above, it is still compliant to 40 specs.Quote:
Originally Posted by Hodge
tappin from tassie
I had mine in manland and it just rusted away, now running a mates Coonara style heaterQuote:
Originally Posted by biggqwesty
Yea going to treat this one and paint her up..
Bloody 4.5' flu though.
What a bastered size!!
A 1/4 inch torque wrench and a new rocker.....
Sent from my SM-G925I using Tapatalk
A rivnut kit.
I borrowed a mates one and it was tops, thought of so many uses, so I got my own.
ha ha u should live over here i can get it easy :)Quote:
Originally Posted by biggqwesty
Haha. Yea tell me about it.
So it's a standard flu size is it??
Just threw out 3 lengths bummer ehQuote:
Originally Posted by biggqwesty
What kit did you get?Quote:
Originally Posted by Rocket55
Got one of these, middle of the road, dearer than the cheapies, cheaper than the dear ones...Quote:
Originally Posted by biggqwesty
http://www.ebay.com.au/ulk/itm/261881538801
I was looking at the stainless kit.. can think of many uses for it. Just not sure I can justify $250 atm..Quote:
Originally Posted by Rocket55
I offered $140 on the kit I linked and he accepted it.Quote:
Originally Posted by biggqwesty
Ow there alloy. Nice one..
After seeing this thing used first hand on Jonothans snorkel, I'm getting one !Quote:
Originally Posted by Rocket55
That's what I used for my snorkel also. Never used one before and first go straight into the A pillar, "don't stuff it up" but it was so easy and neat. I'm thinking compressor mounting, mounting stuff to the fire wall (catch can), holding the CC intercooler down, airbox mounts in radiator support panel, plus many others...Quote:
Originally Posted by Hodge
Thanks fellas! Now i have to get one of these fandagled tools too now!
Sent from my SM-P600 using Tapatalk
You wont regret it. Just make sure you get one that can do larger ones like 8 and 10mmQuote:
Originally Posted by mudski
The pneumatic ones are even better again.
You'll need your Pop Eye arms on to pull up a 10mm steel rivnut manually.
Spend the extra pennies and get a neumatic one. Or spend more time doing threedogs favorite destressing excercise ;)Quote:
Originally Posted by Rocket55
This is the kit I'm looking at.. has the bigger gun, and 8mm stainless so should allow 10mm alloy and maybe steel..
I'll be buying once diffs are in..
so which one is itQuote:
Originally Posted by biggqwesty