GU centre console removal

Quote:

---

Originally Posted by gubigfish

I'm trying to do this to get to the back of the centre console so I can mount my new UHF there. I've removed the first bit undid the screws mentioned but it still seems to be held in by something. Any ideas? Looks like someones tried to staple the base I can see two divets with what looks like staples in them, its the only thing I can think off thats still holding the centre console in place.

---

Have you undone the 2 screw bolts in the bottom of the actual console? 2 in the bottom and 2 under the ashtray.

Quote:

---

Originally Posted by MudRunnerTD

Have you undone the 2 screw bolts in the bottom of the actual console? 2 in the bottom and 2 under the ashtray.

---

Yeah I found some extra ones under the lid at the back above where an ashtray could go and once I removed that the back of it was able to be removed and found the 2 at the back of the centre console.

Cheers

Has anyone removed the panel in front of the centre console that has the sub tank switch and power outlet in it? I guess the centre console has to come out to do it?
cheers
Lana

If your talking in front of the gear stick leaver you need to take the shroud off, 4 screws 2 on each side and one in the ashtray. Should be pretty obvious after that.

Quote:

---

Originally Posted by gubigfish

If your talking in front of the gear stick leaver you need to take the shroud off, 4 screws 2 on each side and one in the ashtray. Should be pretty obvious after that.

---

and remember to unplug the ash tray light before removing the console out. Mine finally busted after forgetting on numerous occasions. :frown:

Quote:

---

Originally Posted by mudski

Yeah that Baintech USB socket is crap. Useless for charging as its only 1amp. My tablet and phone will still go flat when plugged into it. Need a minimum of 2amp these days. Something else to change....

---

Same deal with this Narva USB socket I fitted into my second glovebox.

Attachment 72248

Can anyone recommend a dual USB socket to replace it which WILL charge a tablet being used (& preferably with a phone plugged in too)?

Quote:

---

Originally Posted by Cuppa

Same deal with this Narva USB socket I fitted into my second glovebox.

Attachment 72248

Can anyone recommend a dual USB socket to replace it which WILL charge a tablet being used (& preferably with a phone plugged in too)?

---

@jaysee. He got a hold of a 3.5a one I believe. 3.5a would be perfect.

@Cuppa check out jaycars website there is a few they stock now rated at 2.1 amp per output so a total of 4.2 amp. I put 2 lots in mine for the kids ipads (ipad 4 and ipad air) and they work well...... providing the kids havent stuffed the cables up they use 😩. Thats another drama

Sent from my SM-G920I using Tapatalk

The slight issue with 2.1A socket is they work fine if your not using a power hungry app like mapping software. I have a 2A socket in the rear and it wont charge my tablet if Im using Memory map. If using my 3A ciggie socket to USB Adpator the tablet will charge.

Thanks Mark & Mike, have just ordered one from my local Jaycar outlet. New model - will take 3 days to get it in. Comes with panel & surface mount & looks like it should fit the same as the existing one.

Older model with same 4.2a output is on special at the moment, but I wasn't sure if it had the same mount as my existing one - so paid a bit more for the new one which does. Probably a good buy for anyone who doesn't need the extra 'plastic surround' though.

Photo of my existing one, just 'cos I'm not sure which is the 'Panel' mount, & which is the 'Surface' mount, although I'm guessing mine is 'Panel'. :)

Attachment 72251