Printable View
Update of drawers.
http://img.photobucket.com/albums/v5.../WP_000239.jpg
Have purchased my locks now will post them up tomorrow. Getting the carpet tomorrow then all I need to do is get a latch for the fridge slide. Hopefully should be done by mid next week. Never trust another persons measurements. The plan was way out but all fixed now.
have you weighed them yet ?
Nope! haha and not sure if I will!Quote:
Originally Posted by threedogs
So a few things have been happening.
I have purchased the Pillar pod, some gauges (saas), GoPro4 (For the Yak) and a wheelie bin bag.
http://img.photobucket.com/albums/v5...110_164157.jpg
My have also been working on the drawers, this is where they stand today, going to hopefully finish them tonight. Bolted in, but will still need to do the sides later!
http://img.photobucket.com/albums/v5...111_172617.jpg
http://img.photobucket.com/albums/v5...cf47dbf598.jpg
http://img.photobucket.com/albums/v5...111_201003.jpg
Did you not see AB's Red Back wheelie bags ,
what is the car off to the right in pic ?
Also I undid the bottom seatbelt bolt and tucked it all down that top trim
Ahhh Thanks threedogs, I was wondering what to do with the seatbelts!
The car on the right is an old VW Beetle convertible - another project for another day!
I did not see Redbacks Wheelie bins, but this ridge ryder was only $39 on special so why not!
Threedogs, may I also ask what you used to put that mesh on the bonnet with the intercooler intake? & what you used to secure it Cheers
I've since taken that and the engine cover off.
when cut to size I just pried up the middle of the scoop with a steel rule
and slid it in, never moved, sort of spring loaded
Are you getting an aftermarket scoop.?
Bit more work done today, Under the fridge slide, will be putting a nice piece of Jarrah varnished. Will be fitting it in Friday which is the next designated day off from work!
I went a bit berserk with the angled alloy but the carpet needed it! Looks quite nice too imo! Still need to carpet the inside, I will just do the floor then paint the inside sides! with some satin black.
Pics..
http://img.photobucket.com/albums/v5...112_200008.jpg
http://img.photobucket.com/albums/v5...112_195957.jpg
http://img.photobucket.com/albums/v5...112_195757.jpg
A nice latch on the fridge slide to secure too! Once fitted, we will do the sides in some more ply and carpet it. Im thinking of a baintech panel to put on the left side.. The right can be extra storage.
Update*
So have had the NADS installed, BOOST, EGT, Pillar pod, 3" Dump pipe & Catch can. Temps run 300-350. Even driving up the expressway hill.
Last week the car had developed this weird shudder, when I would pull up to the lights, then would idle fine. It only happened a handfull of times. Put some diesel additive in the fuel, to ensure it was not that. Found one of my oil catch can breather pipes came off (Own fault for fiddling) so I put a clamp on that.
After more research it appears I think it may be my DMF (Dual Mass flywheel) playing the culprit after a search of the symptoms. With the air-con on it does not shudder, as it gets the revs higher. We have just hit a heat wave too. So I'm sure its expanding more than it has been in the cool climate lately. I will have to get it further investigated.
Picked up an Ebay special Alloy roof tradesman cage. Which I fitted the other day.
http://img.photobucket.com/albums/v5...44926678_n.jpg
Missus is going back to university and saving for our wedding. So I will be saving pennys SLOWLY for the dual battery system. I have picked up a Baintech Dual battery kit 100A for $69 off a sale which I have, So I just need to get the other required parts. I also purchased a Baintech power panel with, Cig sockets, USB, Voltage too.
nice bus/build up bud.. got the same rig look forward to the mods...