OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Replies
    25
    Views
    8,363

    More humans on the road nowadays are far more...

    More humans on the road nowadays are far more intellectually challenged than any roo.
  2. Replies
    25
    Views
    8,363

    I disagree, Emu's are the dumbest animals on the...

    I disagree, Emu's are the dumbest animals on the planet. Bloody kamikaze feather dusters
  3. Certainly important - I used an old head bolt ,...

    Certainly important - I used an old head bolt , grinded flat a bit on one side.
    \
  4. Replies
    0
    Views
    1,886

    DIY valve spring compression tool.

    A while ago I posted a question about replacing a head gasket. many thanks to all who helped with advice.
    The head is off , and the valves looked they could do with a clean , one was not even...
  5. Thread: Gq backfiring

    by MB
    Replies
    15
    Views
    4,960

    Now that makes perfect sense to nuffy me AB Mate,...

    Now that makes perfect sense to nuffy me AB Mate, ping pong, would explain the valves open exploding with inwards & outwards ignition after TDC/BDC if that’s correct?


    Sent from my iPhone using...
  6. Replies
    501
    Views
    294,532

    FWIW: It was honestly a genuine question as...

    FWIW: It was honestly a genuine question as ‘Cyclists’ well known experienced....arrogantly traverse our daily work routes enroute to Selfish Coffee’s [emoji856]
    Thinking I should increase my own...
  7. Replies
    15
    Views
    6,391

    Mind Blown!! 81257

    Mind Blown!!

    81257
  8. Replies
    26
    Views
    10,825

    AB, yep, more work and I am just about over the...

    AB, yep, more work and I am just about over the fiddling around to be honest. I will have a look tomorrow as the config you suggest is probably the best. Thanks.
  9. Replies
    26
    Views
    10,825

    That's interesting AB. I did have a pair of 2"...

    That's interesting AB. I did have a pair of 2" projector lights and took them off as they got so damn hot I was worried about them melting the housing they were in. I will have another look at...
  10. Did you even look at the specs Arfa. Try some...

    Did you even look at the specs Arfa. Try some offset bushes in the radius arms and setback bushes in the rear if the arms. Get rid of any RTC damper as this hides alot of issues in the steering...
  11. FWIW for the last 40+ years I’ve always taken my...

    FWIW for the last 40+ years I’ve always taken my cars to a specialist wheel alignment/suspension shop. That’s all he does and has ever done. Never had an issue, I always rotate all five tyres and...
  12. I think you should expect your money back . If it...

    I think you should expect your money back . If it were me I would be making that firmly but politely clear to whoever is in charge & telling them that both a) it was fine before they adjusted it & b)...
  13. Replies
    383
    Views
    115,463

    Agreed AB Mate! Good Hard Yakka memories as a...

    Agreed AB Mate!
    Good Hard Yakka memories as a kid too as late as the early 80’s having to travel with Dad further out of our ‘Green Wedge’ just started then I believe to the likes of outlying...
  14. Replies
    383
    Views
    115,463

    I remember having cuts all up my arms, legs and...

    I remember having cuts all up my arms, legs and on my face from gathering enough blackberries for my mum to make a pie.
    It was always worth every cut.
  15. Replies
    383
    Views
    115,463

    oh some wonderful memories on here.......... I...

    oh some wonderful memories on here..........

    I remember the Black and White TV - Test Patten after 11.00pm
    my Father going to Vietnam in '67
    driving across the Nullarbor Xmas '68 - was just a...
Results 1 to 15 of 39
Page 1 of 3 1 2 3