OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Thread: Scantools

    by my third 256
    Replies
    8
    Views
    3,852

    this site has it all...

    this site has it all
    http://www.ecutalk.com/diesel.aspx
  2. Replies
    10
    Views
    6,188

    Yet again Daniel you shit me........... bloody...

    Yet again Daniel you shit me........... bloody good work mate I always love seeing your creations... wish I had some of your talent.!!!
  3. Replies
    17
    Views
    29,424

    That is a hell of a lot of welding, plenty of...

    That is a hell of a lot of welding, plenty of thought gone into them, well done
  4. Replies
    21
    Views
    5,869

    Pics mate. How bad is it?. Knowing a 3ltr the...

    Pics mate. How bad is it?.

    Knowing a 3ltr the ic would have had oil threw it.. So would have been difficult to weld to start with..

    But they should have cleaned it out, purged it and then...
  5. Replies
    9
    Views
    2,540

    Yes, but you would need to use a regulator with a...

    Yes, but you would need to use a regulator with a panel of that size.
  6. Replies
    8
    Views
    5,150

    def idle up

    def idle up
  7. Thread: Need help tie rod

    by Robo
    Replies
    8
    Views
    2,348

    Freeze lubricant spray. The sudden temp...

    Freeze lubricant spray.
    The sudden temp difference helps to open & allow lube to penetrate a little better.
    about $20 a can but worth it.
    Becomes very hand for stubborn tie,ball joints etc.
  8. Replies
    21
    Views
    15,420

    I think the hardest part about putting Toyota...

    I think the hardest part about putting Toyota parts in a Nissan is placing your testicles In the jar On the shelf and buying a skirt...
    :D
    Toyota drivers put Nissan parts in as their already in...
  9. Replies
    3
    Views
    1,369

    Hi lift jack attachment diy

    Here's a gizmo I used to make for 4x4s that didn't have plastic bumpers.
    It fits over the foot of the hi-lift and held in place with a 1/2" GRADE 8 Bolt.
    I made it for some comp trucks so the could...
  10. Replies
    1,861
    Views
    672,891

    yes it is at the chassis end Mega. If you have...

    yes it is at the chassis end Mega.

    If you have a look at this pic and note that the top mount is in line with the factory mount (in fact it connects to this position for strength) and the bottom...
  11. Replies
    11
    Views
    4,424

    not necessarily, from memory they were originally...

    not necessarily, from memory they were originally designed for marine applications hence the negative isolating (got me stuffed why) but can be wired both ways.

    there is a series of installation...
  12. Replies
    11
    Views
    4,424

    not 100% but I think Cuppa may run this system

    not 100% but I think Cuppa may run this system
  13. Not me, I just fitted LED's to all lights. Can...

    Not me, I just fitted LED's to all lights.
    Can now leave them on for hours with no worries!

    Would be possible if you really wanted to, just find the interior light circuit on the fuse block....
  14. Replies
    73
    Views
    76,209

    Grab some quilt stuffing and put a couple of...

    Grab some quilt stuffing and put a couple of layers around the inside edges if the box until Its around 100mm thick, and your 6x9's will sound like subs...
  15. Replies
    2
    Views
    1,527

    -15c Sleeping Bags

    http://www.ebay.com.au/itm/Beyond-outdoor-MOUNTAIN-VIEW-15-C-Sleeping-Bag-220x80cm-3D-NEW-style-/121139182843?pt=AU_Sleeping_Gear&hash=item1c34753cfb#ht_7208wt_1399

    -15c sleping bags (extreme...
Results 1 to 15 of 25
Page 1 of 2 1 2