OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 14 1 2 3 4

Search: Search took 1.00 seconds.

  1. Thread: General Banter

    by mudnut
    Replies
    269
    Views
    73,851

    Glad it burst while you were stopped and no-one...

    Glad it burst while you were stopped and no-one got hurt. That could have been so much worse. Enjoy the rest of the trip.
  2. Thread: General Banter

    by jay see
    Replies
    269
    Views
    73,851

    That's all the bad luck for you mate. Enjoy the...

    That's all the bad luck for you mate.
    Enjoy the rest of the trip. Brilliant part of the world your heading to..

    Sent from my Pixel 7 using Tapatalk
  3. Replies
    269
    Views
    73,851

    Geez, that is a run of bad luck mudski! How many...

    Geez, that is a run of bad luck mudski!
    How many K's had you done on those tyres in 7 years?
  4. Replies
    651
    Views
    162,004

    Its big enough. all miles, have a safe and...

    Its big enough. all miles, have a safe and trouble-free trip
  5. Replies
    651
    Views
    162,004

    Wiring issues again. FI Interchiller has been...

    Wiring issues again. FI Interchiller has been under performing, not chilling adequately, so went chasing the switch valve, found it down on volts so am going to upgrade the line size, however plugged...
  6. Replies
    940
    Views
    181,987

    Couple of comments. If you do this make sure its...

    Couple of comments. If you do this make sure its a body on job, body off is a mass of complication and heartache. Also the can will be heavier as you have to factor in the frame of the tray, tray...
  7. Replies
    940
    Views
    181,987

    I agree Marko you’ve got an awesome GU TD42 wagon...

    I agree Marko you’ve got an awesome GU TD42 wagon plus fantastic accessories. But I’m going to be devil’s advocate and ask why you want to chop the back off? Any GU wagon can be a touring legend....
  8. Replies
    940
    Views
    181,987

    Looking good Markie, Phils is a CAM Fabrications...

    Looking good Markie, Phils is a CAM Fabrications kit with an at home install then engineered. . I know DMW do chops in Queensland along with GVM upgrades and chassis extension aswell, not sure who...
  9. Replies
    651
    Views
    162,004

    Definitely 60 degree taper on the Y61 17" factory...

    Definitely 60 degree taper on the Y61 17" factory alloys, and the handbook for my 2015 GU Y61 wagon states 97 ft/lbs tension. I do a recheck after a few hundred ks, and also re-do the tension anytime...
  10. Replies
    651
    Views
    162,004

    Spoke with PAP this morning about stud strength...

    Spoke with PAP this morning about stud strength options and applicable nuts.

    The factory studs are the go, however their aftermarket studs are 'marketed' as being stronger and cheaper than the...
  11. Replies
    651
    Views
    162,004

    Genuine Nissan GU steelies. You’ll find them...

    Genuine Nissan GU steelies. You’ll find them cheap 2nd hand online.

    88313
  12. Replies
    651
    Views
    162,004

    I bought 3 packs of 5 from 3 vendors, first set...

    I bought 3 packs of 5 from 3 vendors, first set arrived today, have a few spares now, fitted them this arvo, good quality fit and nice and fat for a good seal.
  13. Replies
    940
    Views
    181,987

    Gottcha, yes the HID are not approved globes full...

    Gottcha, yes the HID are not approved globes full stop, but the 7" round inserts are. PLOD may try to disagree but they are stamped on the light and VASS approved.
  14. Replies
    940
    Views
    181,987

    88294 88295

    88294

    88295
  15. Replies
    940
    Views
    181,987

    I had the same concerns, but I have been running...

    I had the same concerns, but I have been running them for two years now and not one on coming car has flashed me.
    They give you Euro-car-like clear white light. Much safer.
Results 1 to 15 of 200
Page 1 of 14 1 2 3 4