GQ Patrol RH/LH front inner guard rubber splashguard template

[PeeBee]

Does anyone have a template of these rubber sheets , preferably on say a known scale like an A4 sheet they could share? I need to replace mine however the units will be too short for the 25mm body lift. I could buy one from PAP for $60 but it will be wasted in the main, plus we have a very large rubber shop on site and they are idle, so I could easily get a couple made in 2 -3mm rubber.

Like this, but for a GQ, not the plastic one up the top.

https://www.ebay.com.au/itm/122760840789

or there are these ones out of hdpe

https://munji.com.au/products/copy-of-composite-inner-guard-replacements-gq-patrol?variant=42294726754500

[PeeBee]

Maybe another request is for someone to stick a few A4 sheets together, remove one of the splash sheets from their guard and trace out the shape for me, then post a number of shots so I can replicate om site? Please!!!

[PeeBee]

OK, massive response, thanks. i have decided to go with the Munji 1" body lift set up and nutserts

[PeeBee]

I will make a template of these for rubber sheet duplication into the future for others.

[MudRunnerTD]

Maybe another request is for someone to stick a few A4 sheets together, remove one of the splash sheets from their guard and trace out the shape for me, then post a number of shots so I can replicate om site? Please!!!

Apologies mate, Been slack. 100% just cut your own. They are actually very simple. I have never had a template and just cut as required. When you buy the rubber from Clarke Rubber make sure you chose a lamenated rubber with ain internal clothe fabric as it will hold together much better. Really easy to cut but the fabric will stop crack runs.

No Nutserts needed either. I assume you have bought at least 1 set of clips etc for pushing into holes. Just use a variety of those. dont over think it. Its a splash guard.

[MudRunnerTD]

I assume you have something like this kit mate? No nutserts needed

https://www.ebay.com.au/itm/394664279325?_trkparms=amclksrc%3DITM%26aid%3D1110 018%26algo%3DHOMESPLICE.COMPLISTINGS%26ao%3D1%26as c%3D20210609144404%26meid%3Da27b0b5615be4cddb27c64 febfd6e9ae%26pid%3D101196%26rk%3D4%26rkt%3D12%26sd %3D145260763620%26itm%3D394664279325%26pmt%3D1%26n oa%3D0%26pg%3D4429486%26algv%3DCompVIDesktopATF2V3 WithQueryItemRecallV3%26brand%3DUnbranded&_trksid=p4429486.c101196.m2219&amdata=cksum%3A394664279325a27b0b5615be4cddb27c64f ebfd6e9ae%7Cenc%3AAQAIAAABILHyIAEaemKG0mx4REjf%252 BHxECBsXtSkNHsCLmXz%252FJyCDeX%252FaDb78456J9CQJiW kf1kJKEbH7Hum7R71Szu1Y8Dg5ODgTZcBGnTdRWuAqYi%252BW 0KmB7Smj%252F%252BvtxvH4Xav%252BmpyIcBJu2GelAqsLrZ o3Dk4AhAqgxP9kQxRW7QLRSBj%252FGY4eZ8I6uFbkmPAv1SeA 16%252FAgbfgyJhIWkIxK4iwH5h76iFKoCBULCkP5TzQkuyUt0 PZvppCapclQsqARMNunnXqYF4hj16H6%252B5xmrQC9Mg%252F cEsJUBRzdzWxx0cZ%252BmT2XAIIIADDCTFxOLB%252F%252FY ILje72%252BktGfSu3OsrLur8MoiQxr99vG%252B5w5atuBqvB v%252FPJZArD1OFC2HQNTqfo6%252F8pyg%253D%253D%7Camp id%3APL_CLK%7Cclp%3A4429486

[PeeBee]

I assume you have something like this kit mate? No nutserts needed

https://www.ebay.com.au/itm/394664279325?_trkparms=amclksrc%3DITM%26aid%3D1110 018%26algo%3DHOMESPLICE.COMPLISTINGS%26ao%3D1%26as c%3D20210609144404%26meid%3Da27b0b5615be4cddb27c64 febfd6e9ae%26pid%3D101196%26rk%3D4%26rkt%3D12%26sd %3D145260763620%26itm%3D394664279325%26pmt%3D1%26n oa%3D0%26pg%3D4429486%26algv%3DCompVIDesktopATF2V3 WithQueryItemRecallV3%26brand%3DUnbranded&_trksid=p4429486.c101196.m2219&amdata=cksum%3A394664279325a27b0b5615be4cddb27c64f ebfd6e9ae%7Cenc%3AAQAIAAABILHyIAEaemKG0mx4REjf%252 BHxECBsXtSkNHsCLmXz%252FJyCDeX%252FaDb78456J9CQJiW kf1kJKEbH7Hum7R71Szu1Y8Dg5ODgTZcBGnTdRWuAqYi%252BW 0KmB7Smj%252F%252BvtxvH4Xav%252BmpyIcBJu2GelAqsLrZ o3Dk4AhAqgxP9kQxRW7QLRSBj%252FGY4eZ8I6uFbkmPAv1SeA 16%252FAgbfgyJhIWkIxK4iwH5h76iFKoCBULCkP5TzQkuyUt0 PZvppCapclQsqARMNunnXqYF4hj16H6%252B5xmrQC9Mg%252F cEsJUBRzdzWxx0cZ%252BmT2XAIIIADDCTFxOLB%252F%252FY ILje72%252BktGfSu3OsrLur8MoiQxr99vG%252B5w5atuBqvB v%252FPJZArD1OFC2HQNTqfo6%252F8pyg%253D%253D%7Camp id%3APL_CLK%7Cclp%3A4429486

Thanks Daz, yes have a couple of these with assortment, in all honesty they are a bit of a junk bin with quality poor and also they dont fit like the factory ones. Anyway i have adopted the nutsert after the hassles with the VASS engineer wanting everything non standard nertsert'd or crush tubed, so the operation is quick and permanent and easily removeable without damage. The new ones are expensive for what they are, but better than a non compliance at the inspection and it also hids some hose and pipes.

I have gone with these as not a single response to the template.

https://munji.com.au/products/copy-of-composite-inner-guard-replacements-gq-patrol?variant=42294726754500

[MudRunnerTD]

Thanks Daz, yes have a couple of these with assortment, in all honesty they are a bit of a junk bin with quality poor and also they dont fit like the factory ones. Anyway i have adopted the nutsert after the hassles with the VASS engineer wanting everything non standard nertsert'd or crush tubed, so the operation is quick and permanent and easily removeable without damage. The new ones are expensive for what they are, but better than a non compliance at the inspection and it also hids some hose and pipes.

I have gone with these as not a single response to the template.

https://munji.com.au/products/copy-of-composite-inner-guard-replacements-gq-patrol?variant=42294726754500

Oh they look pretty!! hvae not seen those before.

[PeeBee]

Oh they look pretty!! hvae not seen those before.

Yeah the attractant was they are configured for standard, 25 or 50mm body lift. I am running 25 for the s/c snout clearance and don't want to highlight this to the engineer. I liked the nutsert idea as well because it fell in line with his demands.

[BrazilianY60]

Hi PB. I´ve been working too much lately and have just been able now to log in to check what's going on with the good old folks here.

Mines are toasted and ripped but I won't dedicate that much effort to it. My plan is to buy a say 1mm or 2mm rubber mat and cut it to shape "in place". Doesn't seem like a big deal really.

[PeeBee]

Hi PB. I´ve been working too much lately and have just been able now to log in to check what's going on with the good old folks here.

Mines are toasted and ripped but I won't dedicate that much effort to it. My plan is to buy a say 1mm or 2mm rubber mat and cut it to shape "in place". Doesn't seem like a big deal really.

Agree, the opportunity for me is a large rubber department on site, heaps of rubber and labour avail, instead of rooting around when I get off roster and blowing half a day if a template was avail or someone was will to make one for me. In the ned I went with these as they will be waiting for me when I get home and seemed better value than the factory originals.

[BrazilianY60]

When you say there is a rubber department on site, does it means they are working on the project with you and there may be off cuts and such that you could use for free?

[PeeBee]

When you say there is a rubber department on site, does it means they are working on the project with you and there may be off cuts and such that you could use for free?

Yes that is correct, but the obvious issue is the economy and sense in bringing it 10hrs on planes or sourcing at home.