G'day All Thanks for having me!

[Basco]

G'day all just posting a quick hello!

This forum was a massive help on the weekend giving me enough confidence and the information needed to have a go at a swivel hub rebuild on my ute.

A bit about myself: My names Jarrod, I'm living around the Newcastle NSW area at the moment and my pride and joy is an 06 TD42ti GU Ute! I would post a pic of it but I don't know how to do that yet haha

just a quick question while I'm here; In my swivel hub rebuild kit there were 2 silver washers (one for each side in guessing) with a square tab on the inside of one side. I didn't notice any washers like this on my ute when stripping the hub down are they needed?

Thanks again for having me and for all the help and info!

[MudRunnerTD]

G'day all just posting a quick hello!

This forum was a massive help on the weekend giving me enough confidence and the information needed to have a go at a swivel hub rebuild on my ute.

A bit about myself: My names Jarrod, I'm living around the Newcastle NSW area at the moment and my pride and joy is an 06 TD42ti GU Ute! I would post a pic of it but I don't know how to do that yet haha

just a quick question while I'm here; In my swivel hub rebuild kit there were 2 silver washers (one for each side in guessing) with a square tab on the inside of one side. I didn't notice any washers like this on my ute when stripping the hub down are they needed?

Thanks again for having me and for all the help and info!

Hi mate, welcome and glad my thread was helpful. The wasger your talking about is for a GQ front end without the round lock nut. The washer bends over to lock the 54mm nut. Your GU has a e
Round nut with 2 phillips head screws.

[Basco]

Hi mate, welcome and glad my thread was helpful. The wasger your talking about is for a GQ front end without the round lock nut. The washer bends over to lock the 54mm nut. Your GU has a e
Round nut with 2 phillips head screws.

Can't thank you enough mate was a great help and a great thread!
77547
Thats the washer that came in my kit (if i uploaded the picture right), I thought it may have gone under the round nut in the gu but if its not needed I'll remove it tomorrow after work! cheers for clearing that up for me mate!

[MudRunnerTD]

Can't thank you enough mate was a great help and a great thread!
77547
Thats the washer that came in my kit (if i uploaded the picture right), I thought it may have gone under the round nut in the gu but if its not needed I'll remove it tomorrow after work! cheers for clearing that up for me mate!Have a look at the pics below. I think that is the washer that goes under the first nut.

http://www.nissanpatrol.com.au/forums/images/imported/2019/01/150.jpg

http://www.nissanpatrol.com.au/forums/images/imported/2019/01/151.jpg

The Lock washer is a bit bigger i think as seen in this pic below

http://www.nissanpatrol.com.au/forums/images/imported/2019/01/152.jpg

Did you put a washer under the first nut?

Sent from my SM-G955F using Tapatalk

[MudRunnerTD]

So being a GU you have the setup at the bottom. The round nuts in red are the GU alternate bearing nuts. No washer detailed.

http://www.nissanpatrol.com.au/forums/images/imported/2019/01/153.jpg

If you have Manual Hubs you have the nuts in Red then the middle alternate detail.

Sent from my SM-G955F using Tapatalk

[AB]

Welcome to the forum mate and feel free to ask any questions.

[Dhuck]

Welcome to the forum mate

[4bye4]

G'day mate and welcome to the forum.