hi all im new to this site !!!!

[qldtrucker]

I have owned a mq 3.3 diesel.I now own gq 4.2 diesel and a gu 3L diesel ,now replacing wheel seal on gq after 417,000km and i fuel problems with 3L

[growler2058]

Gday mate welcome aboard theyre a good friendly mob here full of useful info and advice

[qldtrucker]

thanks m8t sounds good

[Bob]

Welcome along mate. Join in and enjoy

[qldtrucker]

any one know where to get a 58.2mm spanner

[Bigrig]

G'day mate - welcome aboard. Great people, information and laughs on here mate, so feel free to join in and make the most of it. Enjoy!!

[Bigrig]

any one know where to get a 58.2mm spanner

What's it for?? Have you tried Trade Tools Direct?? They have some pretty big spanner sets.

[growler2058]

http://www.nissanpatrol.com.au/forums/showthread.php?2067-How-do-i-change-a-gu-cv&highlight=wheel+bearings click on this link mate i used a pin punch to loosen mine this may help

[Dhuck]

Welcome to the forum mate

[AB]

Welcome to the forum mate, feel free to ask any questions and join in the conversations.

[qldtrucker]

thanks guys 58.2mm is for rear wheel axel nut that holds seals and bearings in place

[YNOT]

I have owned a mq 3.3 diesel.I now own gq 4.2 diesel and a gu 3L diesel ,now replacing wheel seal on gq after 417,000km and i fuel problems with 3L

If you have oil leaking down the brake backing plate your problem is a leaking inner axle oil seal, you don't need the big spanner to replace that seal.

Tony

[qldtrucker]

bearing got warm , so need to check it out ,but oil was leaking as well

[YNOT]

Fair enough then.

Tony

[qldtrucker]

hi ynot im at cedar vale , have you had much to do with gu 3l ?

[YNOT]

hi ynot im at cedar vale , have you had much to do with gu 3l ?

I own a 3l and have done the engine saver mods etc.

Tony

[qldtrucker]

we bought 2001 3l in december engine light now on 707 ithink the code was who should i take it too ? i do most work my self but if it fuel pump im not going there

[katwoman]

Welcome to the forum, it you cant find what you want here, it does not exist..

[qldtrucker]

thanks katwoman great to be here

[YNOT]

we bought 2001 3l in december engine light now on 707 ithink the code was who should i take it too ? i do most work my self but if it fuel pump im not going there

0707 Fuel Injection Timing Control System
Circuit malfunction, Injection Pump Control Unit failure, Poor fuel quality

It's not looking good!
Don't take it to Nissan, there's a diesel specialist in the Springwood/Underwood area (the name escapes me at the moment) that would have a better idea of what to do next.

Tony

[YNOT]

By the way, welcome to the forum.

Tony

[qldtrucker]

that would be diesel australia they say about $4500 if need new pump thanks any way Tony .

[YNOT]

It may not need a pump, it could be something as simple as a leaking lift pump allowing air into the fuel system. That can log the same code.

Tony

[qldtrucker]

there is realy small air bubbles comming into the filter , i have put clear hose on both sides of fuel filter ,

[DX grunt]

G'day mate

Welcome to the forum.

Take care out there.

Ross
DX grunt

[Sir Roofy]

Welcome aboard mate

[big_fletch]

Welcome to the forum mate, great to have another member aboard

[qldtrucker]

thanks again all, realy glad i joined this site. sounds like we have mechanics ,autoelects and a bit of every thing here

[big_fletch]

Haha yer pretty much mate, hopefully between all the members here we can answer all the questions you might have

[wildgu6]

Welcome aboard buddy,
Great bunch of people here with a s*** load of knowledge, experience and adventures to share.
Plenty of good laughs along the way as well.
Surf around and join in where ever you feel comfortable.

Hope you have a great 2011.
stay safe & Enjoy the ride.


Cheers Pete

[Dark 1]

Welcome mate, have a poke around & join in when your ready.

[rfrom7inoz]

Welcome to the forum. Enjoy!

[Finly Owner]

Hi and welcome to Nissans Nut House qldtrucker

R U thinking "Deisel Australia" Tony?
if so 45-47 Allgas St Slacks Ck ph 3808 6988

Tim

[qldtrucker]

thanks kelvin , do you have a web site for your asl lights and do you sell clearance lights ? thanks mate

[timbar]

G'day mate - welcome aboard join in and have fun mate plenty to do see and if u have any problems just ask and im sure u will get an answer ENJOY and WELCOME

Tim

[qldtrucker]

does anyone have any clue how to press rear wheel bearing off without a press. all good now found a press

[YNOT]

I don't know how to remove them even with a press. A couple of years ago when I was working for a Ford dealer we tried to press of a Maverick rear wheel bearing. Even a 30 ton press couldn't move it. We repacked the bearing in place and never had any trouble so the bearing must have been OK.

Tony

[Maxhead]

G'Day and welcome to the forum mate

[qldtrucker]

thanks tony , I took it to john deer at beaudesert the boys there pressed it off for me . Need to replace outer seal too

[YNOT]

Good stuff. How was the bearing?

Tony

[qldtrucker]

they look ok but one seems to be a bit sticky .

[Clunk]

g'day mate, welcome aboard the forum and enjoy

[mrcrazydude]

Welcome to the forum mate!

[patch697]

To all new members & those member who have joined in the last 4 months I'd like to introduce myself

Hi all my name is Paul (patch697) & I am the Super Moderator here on the forum. I have been away for a spell & there will be a lot of new members who haven't met me yet so I'd like to extend a worm welcome from myself to you all & if you have any question or need any help don't hesitate to ask.

I hope you all enjoy the forum.

Cheers
Paul