-
1st June 2020, 10:06 AM
#1
Nissan / Airtec Snorkel head
Does anyone know if there is a different head that can fitted onto the Nissan / Airtec snorkels. They look terrible and don't seem large enough.
Alternatively, does anyone know if you can replace the Nissan / Airtec snorkel with a Safari? Do the holes match up???
Thanks.
-
-
1st June 2020 10:06 AM
# ADS
Circuit advertisement
-
1st June 2020, 02:19 PM
#2
What size is the snorkel where the ram head sits on? I get the Yota with their 79's come into my work a bit wanting to change the Toyota bowl setup to a Donaldson ram head. So we just need the pipe size to work out what you need.
-
-
1st June 2020, 02:54 PM
#3
Originally Posted by
mudski
What size is the snorkel where the ram head sits on? I get the Yota with their 79's come into my work a bit wanting to change the Toyota bowl setup to a Donaldson ram head. So we just need the pipe size to work out what you need.
That sounds great Mark. The problem with the Airtec is that body of the snorkel follows the A pillar and the bend is in the head. So if you try to put a different head on it, the inlet ends up staring up at the sky.
I measure the diameter of the part that the head slips over as being 87mm.
20200601_141750.jpg
-
-
1st June 2020, 09:29 PM
#4
Ok so we'll say its 89mm, 3 1/2 inch. Theres not a whole lot you can do here. The only option I see is get a 45 degree adaptor which is 89mm ID to slip over the snorkel, then its 89mm OD then you can fit a standard Donaldson snorkel. In the hope that 45 degrees is what you require to see the snorkel head straight.
-
-
1st June 2020, 09:50 PM
#5
Patrol Guru
Mate had an adapter made up (for his Tojo) at the local exhaust shop a few years ago. Might be worth a try?
Time Marches On .....and on ..... and on
-
The Following User Says Thank You to TimE For This Useful Post:
-
2nd June 2020, 11:38 AM
#6
I've stumbled onto a bloke who prints up snorkel adapters on a 3D printer. I'm working with him to see what we can come up with.
-
The Following 2 Users Say Thank You to 10G For This Useful Post:
mudski (2nd June 2020), Rossco (2nd June 2020)
-
2nd June 2020, 02:12 PM
#7
You want to hope it will be strong enough.
-
-
2nd June 2020, 07:15 PM
#8
Travelling Podologist
On the same note
Has anyone successfully managed to fit a cyclonic pre cleaner onto one of these snorkels. If so how & what size (min/max airflow) cleaner? (for TD42i)
2006 4.2TDi ex-Telstra Remote area Camper. 425w roof mounted solar, 360Ah Aux batts, BCDC1240, Onboard hot & cold pressurised & filtered water, (25 litre hot water calorifier), ARB fridge, ARB freezer, Built in kitchen, heaps of easy access storage, 240v, 3” Genie exhaust + dynotune, 2” lift, 3900kg GVM upgrade, second glovebox, ROH Blaktrak steel wheels, Bridgestone D697's (now Toyo RT's), Redarc gauges/pillarpod, Hema HX-1, Icom 450 CB, dual rear view cameras, Onboard 30amp Victron mains charger, second glovebox, dual seat conversion, TPMS, Boss PX7 onboard air with 9 litre tank, 350w inverter, Steel bullbar, Harrop Eaton diff lock (front), Warn winch, Snorkel, Dual spares , 160 litre water tank, 180 litre fuel in two tanks (approx 1200km range) 2010 Tvan Tanami. (incl another 70 litre water tank) with matching wheels/tyres (& 3rd spare)
A Nomadic Life (Blog)
-
-
2nd June 2020, 08:21 PM
#9
He prints the adaptors out of ABS and does something with acetone to make them stronger.
-
-
2nd June 2020, 08:21 PM
#10
Originally Posted by
mudski
You want to hope it will be strong enough.
Originally Posted by
Cuppa
On the same note
Has anyone successfully managed to fit a cyclonic pre cleaner onto one of these snorkels. If so how & what size (min/max airflow) cleaner? (for TD42i)
G'day Cuppa. That's what this blokes adaptors are for, so you can fit a pre-cleaner. As an example:
https://www.ebay.com.au/itm/14361418...torefresh=true
-