OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

User Tag List

Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: TB42 EI Caliper piston dust boot installation

  1. #1
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)

    TB42 EI Caliper piston dust boot installation

    OK, I have looked up the caliper 'sticky', however there appears to be a lot more room to get the dust boot seated than on the twin piston unit - anyone got some tips pls??? Should the seal lip be lubricated or left dry - I have only managed to get about 25% of the circ fitted - the easy bit, but struggling with any further.

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many

     

  3. #2
    The master farter
    mudski's Avatar
    Join Date
    Apr 2012
    Location
    Eltham North
    Posts
    15,596
    Thanks
    8,667
    Thanked 11,260 Times in 6,426 Posts
    Mentioned
    460 Post(s)
    Tagged
    1 Thread(s)
    If its anything like when I rebuilt the TB48 twin potters those rubber boots were a pain to get on. From memory, I lubed up the boots with rubber grease, tucked them into the slot in the housing and pushed the piston in through the boot and into the housing. I do remember having to use a small flat blade screw driver to tuck in the boot in some spots. I did take a few shots before I got them in.

  4. #3
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by mudski View Post
    If its anything like when I rebuilt the TB48 twin potters those rubber boots were a pain to get on. From memory, I lubed up the boots with rubber grease, tucked them into the slot in the housing and pushed the piston in through the boot and into the housing. I do remember having to use a small flat blade screw driver to tuck in the boot in some spots. I did take a few shots before I got them in.
    Thanks for that, I will try and if unsuccessful its down to a brake joint friday as I want this sorted before saturday/sunday for the big change-over.

  5. #4
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)
    Just found this youtube segment, more or less what you are saying Mudski.

    https://www.youtube.com/watch?v=wvOpg7hASLs

  6. The Following User Says Thank You to PeeBee For This Useful Post:

    mudnut (21st June 2018)

  7. #5
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)
    OK, done, took about 30 minutes using the method in the youtube clip, so more or less ready to go for Saturday.

  8. The Following User Says Thank You to PeeBee For This Useful Post:

    mudski (21st June 2018)

  9. #6
    The master farter
    mudski's Avatar
    Join Date
    Apr 2012
    Location
    Eltham North
    Posts
    15,596
    Thanks
    8,667
    Thanked 11,260 Times in 6,426 Posts
    Mentioned
    460 Post(s)
    Tagged
    1 Thread(s)
    Yeah it took me quite a few different shots at it before I got the boots in. I quickly realised there was going to be a certain way to get these boots in, I just had to find it. Tooka bit but I got there.

  10. #7
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)
    I tried your suggestion and the boot was dead easy to seat in the caliper, however I could not stretch the inner opening to get the piston in, maybe tried for 15 minutes then reverted to the youtube method.

  11. #8
    The master farter
    mudski's Avatar
    Join Date
    Apr 2012
    Location
    Eltham North
    Posts
    15,596
    Thanks
    8,667
    Thanked 11,260 Times in 6,426 Posts
    Mentioned
    460 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by PeeBee View Post
    I tried your suggestion and the boot was dead easy to seat in the caliper, however I could not stretch the inner opening to get the piston in, maybe tried for 15 minutes then reverted to the youtube method.
    Yeah I can't remember the exact way I did it but I do remember putting the boot in first, then the piston. Thinking back, maybe I had the boot around the base of the piston, then tucked the boot in position and then slid the piston in. Not sure, but what ever i did worked. Haha!

  12. The Following User Says Thank You to mudski For This Useful Post:

    PeeBee (21st June 2018)

  13. #9
    Legendary
    PeeBee's Avatar
    Join Date
    Sep 2016
    Location
    Melbourne South east
    Posts
    4,709
    Thanks
    4,587
    Thanked 4,672 Times in 2,651 Posts
    Mentioned
    190 Post(s)
    Tagged
    0 Thread(s)
    Is there a trick to bleeding the twin pot calipers? I bought a vacuum kit to draw the brake fluid thru the bleeder, and it does the job, only the air just keeps on coming - obviously not from a leak, just having problems pumping it out of both pots seeing as there is only 1 inlet hose and single bleed point. Am I better off trying to push the fluid back thru the bleed needle and overflow the reservoir?

  14. #10
    ......... MB's Avatar
    Join Date
    Nov 2015
    Location
    Yarra Valley
    Posts
    8,607
    Thanks
    22,735
    Thanked 11,235 Times in 4,951 Posts
    Mentioned
    468 Post(s)
    Tagged
    0 Thread(s)

    TB42 EI Caliper piston dust boot installation

    ‘Gregory’s’ isn’t any “Twin Pot” specific help for your sorry Phil mate!

    As mentioned, working alone I used to use an empty 2L ice cream tub catcher below the reservoirs (clutch or brake) and ‘Tom Thumb’ pump fluids back up the system to overflow instead of downward bleeding, seemed to work pretty well back in the days.
    EDIT: Consult a brake expert before attempting that :-)


    Sent from my iPhone using Tapatalk
    Last edited by MB; 25th June 2018 at 05:41 PM.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •