-
3rd November 2018, 10:31 PM
#8701
Expert
Said good bye to my Patrol for the last time
Sent from my iPhone using Tapatalk Pro
-
The Following User Says Thank You to Yeti's Beast For This Useful Post:
GQtdauto (3rd November 2018)
-
3rd November 2018 10:31 PM
# ADS
Circuit advertisement
-
3rd November 2018, 11:22 PM
#8702
Expert
Originally Posted by
Yeti's Beast
Said good bye to my Patrol for the last time
Sent from my iPhone using Tapatalk Pro
And replaced it with this
Sent from my iPhone using Tapatalk Pro
-
The Following 2 Users Say Thank You to Yeti's Beast For This Useful Post:
Clunk (3rd November 2018), jay see (4th November 2018)
-
4th November 2018, 10:55 AM
#8703
Legendary
Originally Posted by
nissannewby
Well kind of. Grab the line that goes into the little tube that comes out the side of the reservoir. Take this off and place into a bucket. Disconnect fuel solenoid as the pump will pump quicker than you can fill if the engine is running. Crank it a little and top up fluid with fresh stuff until its clean out the return line.
Well I done that, oil looks like it has gone through coming out the return line red as the new stuff. So why am I getting this leak of dirty oil coming from the threaded shaft on top of the box.
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
4th November 2018, 10:57 AM
#8704
Legendary
Originally Posted by
Hodge
Thought I'd fit the radius arm spacers today ...
Lucky I started on the passenger side.
Spacer in. And axle fouls on the Panhard rod.
F*** a duck.
Sent from my SM-N920I using Tapatalk
How did you go.... I haven't fitted spacers so not much help from me.
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
4th November 2018, 11:37 AM
#8705
Legendary
Does anybody know what's under this plate. Can't seem to find it, not even in the manual.
Thinking that there has to be a o ring or something.
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
4th November 2018, 11:46 AM
#8706
Patrol God
Originally Posted by
jay see
Does anybody know what's under this plate. Can't seem to find it, not even in the manual.
Thinking that there has to be a o ring or something.
Sent from my A1601 using Tapatalk
Your thinking is correct. Looking at this drawing you should not have power steering fluid at that adjuster. Looks like the box needs a reseal. The oil will be dirty from the grease in there hence the grease nipple. 20181104_101547.png
Last edited by nissannewby; 4th November 2018 at 11:53 AM.
-
The Following User Says Thank You to nissannewby For This Useful Post:
jay see (4th November 2018)
-
4th November 2018, 12:01 PM
#8707
Legendary
Originally Posted by
nissannewby
Your thinking is correct. Looking at this drawing you should not have power steering fluid at that adjuster. Looks like the box needs a reseal. The oil will be dirty from the grease in there hence the grease nipple.
20181104_101547.png
Thanks mate, I couldn't find a diagram like that. should be able to pop up the plate a replace the o ring yeah?
Will keep updating progress.
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
4th November 2018, 12:05 PM
#8708
Patrol God
Originally Posted by
jay see
Thanks mate, I couldn't find a diagram like that. should be able to pop up the plate a replace the o ring yeah?
Will keep updating progress.
Sent from my A1601 using Tapatalk
Should be possible. You will have to remove that nut to do so. Measure the thread poking out the top before removing so you can put it back where it was. I'm not sure that o-ring will resolve your leak though.
-
The Following User Says Thank You to nissannewby For This Useful Post:
jay see (6th November 2018)
-
4th November 2018, 12:21 PM
#8709
Legendary
Originally Posted by
nissannewby
Should be possible. You will have to remove that nut to do so. Measure the thread poking out the top before removing so you can put it back where it was. I'm not sure that o-ring will resolve your leak though.
So I need to remove the thread as well?
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
4th November 2018, 01:08 PM
#8710
Legendary
Well that thread screws down. Problem is the whole box needs to come out.
Might put it back together and just regease it for now....
Sent from my A1601 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-