-
19th June 2021, 09:03 PM
#10041
.........
-
The Following User Says Thank You to MB For This Useful Post:
-
19th June 2021 09:03 PM
# ADS
Circuit advertisement
-
20th June 2021, 09:18 AM
#10042
Patrol God
Originally Posted by
MB
Thanks Marko mate. When a new starter needed came up on the cards, it was a no brainer really. After seeing jff45 Johns setup and consulting legendary Mudrunner about fitting, it was a done deal.
Extra caution is called for with the oil dipstick for it not to become a welding arc wand vs. the positive terminal with new battery height.
-
The Following 3 Users Say Thank You to Hodge For This Useful Post:
Cremulator (20th June 2021), MB (20th June 2021), Mickhead (20th June 2021)
-
20th June 2021, 03:41 PM
#10043
SPAMINATOR
-
The Following 3 Users Say Thank You to growler2058 For This Useful Post:
Hodge (20th June 2021), MB (21st June 2021), threedogs (7th July 2021)
-
20th June 2021, 03:59 PM
#10044
Patrol God
Like growler.
Changed oil and all filters. So freakin messy with the TD filters. Tidied up some electrics. Subby 'o clock now!
-
The Following 2 Users Say Thank You to Hodge For This Useful Post:
growler2058 (20th June 2021), MB (21st June 2021)
-
21st June 2021, 08:04 PM
#10045
Advanced
Last edited by Dasa; 22nd June 2021 at 09:56 AM.
-
The Following 7 Users Say Thank You to Dasa For This Useful Post:
Cremulator (22nd June 2021), growler2058 (22nd June 2021), MB (21st June 2021), mudnut (21st June 2021), PeeBee (21st June 2021), rusty_nail (21st June 2021), Touses (22nd June 2021)
-
30th June 2021, 01:46 PM
#10046
Advanced
Well that didn't go as planed.
gq.jpg
-
The Following 3 Users Say Thank You to Dasa For This Useful Post:
growler2058 (30th June 2021), MB (30th June 2021), rusty_nail (30th June 2021)
-
1st July 2021, 09:00 AM
#10047
New Roof Rack fitted the past week.
Removed the Old Rescue Basket (Ladder Rack) System, Rhino Basket and 150mm PVC Tube, and fitted a OCAM Alloy Flat Rack and two 100mm PVC Tubes in their place.
20200627_114010.jpg
Old Setup
194463267_135220088598243_1317583590419242582_n.jpg
OCAM Replacement Rack "Less Solar Panel"
206164078_10220921768979432_7631337232521342955_n.jpg
206777283_10220921768739426_7481415004035836849_n.jpg
Part way there
207502436_10220950345853836_4441683164239112285_n.jpg
Finished
More practical storage solution now
Last edited by Grant209; 1st July 2021 at 09:03 AM.
Grant
Penrith Region
Sydney NSW.
-
The Following 2 Users Say Thank You to Grant209 For This Useful Post:
MB (1st July 2021), mudnut (2nd July 2021)
-
1st July 2021, 09:43 AM
#10048
Expert
Originally Posted by
Dasa
Well that didn't go as planed.
Although those circuit breakers are claimed to be waterproof, be warned - THEY ARE NOT. Water does get in around the shafts through the rubber membrane. At least that is my experience. And mine were only subjected to spray/splash and not immersion.
-
The Following 2 Users Say Thank You to Brissieboy For This Useful Post:
Dasa (1st July 2021), MB (1st July 2021)
-
1st July 2021, 05:09 PM
#10049
Advanced
Figured as much looking at it.
So considering the battery location I guess the best option is auto reset breakers then paint it to seal it up.
-
-
2nd July 2021, 04:50 PM
#10050
Installed some 90 deg hose bends on the rear engine cooling loop instead of the externally restrained wire hose formers, so now I have better flow than before - still have to install the kit i purchased from the US that is sized correctly apparently. Also installed a manual breather on the heater circuit so I can get rid of as much air as possible from the cooling circuit. Been a big day.
-
The Following 3 Users Say Thank You to PeeBee For This Useful Post:
MB (4th July 2021), mudnut (2nd July 2021), Rossco (2nd July 2021)