-
30th March 2024, 06:27 PM
#311
Plassy, its a mount frame for an intercooler coil
-
The Following User Says Thank You to PeeBee For This Useful Post:
Plasnart (30th March 2024)
-
30th March 2024 06:27 PM
# ADS
Circuit advertisement
-
30th March 2024, 06:34 PM
#312
-
-
30th March 2024, 06:38 PM
#313
Originally Posted by
MB
“I am most worried about a front end collision and the strong lineal forward facing frame not heading upwards but unfortunately becoming a spear through to beloved little ones”
Sent from my iPhone using Tapatalk
I dont think the frame size has enough column strength and the frame is not substantial enough to resist much MB, its a fairly flimsy configuration I think, looking at the mount location its in the center of the firewall with only a single 90 deg column, 25mm rhs - they should be OK I reckon. If anything it will fold up pretty easily I think.
-
-
30th March 2024, 06:41 PM
#314
.........
Dearly hoping, thanks @PeeBee
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to MB For This Useful Post:
-
31st March 2024, 10:22 AM
#315
Patrol Freak
the frame is less substantial then the bonnet and the engine block, am running some bracing under the joins, hopefully it lasts long enough so i can save up for a proper kit.
if its worth doin its worth over doin
-
The Following 2 Users Say Thank You to garett For This Useful Post:
MB (1st April 2024), PeeBee (31st March 2024)
-
7th April 2024, 01:13 PM
#316
Patrol Freak
put coolant in it and fresh oil. replaced the filters, wired the cooling fan for the intercooler, painted the frame and made a exhaust manifold shield.
just got to sort from the inter cooler to the manifold.. then do all the prestarts.
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
MB (9th April 2024), PeeBee (7th April 2024), Touses (7th April 2024)
-
13th April 2024, 06:39 PM
#317
Patrol Freak
i fired it up today.... need to sort a catch can.
it idles a bit high.. 800 cold it used to be 600.
at idle it got to 100 deg exhaust temp only ran it for 15 mins or so to bleed coolant etc.
ran it.jpg
if its worth doin its worth over doin
-
The Following 5 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (5th May 2024), Cremulator (14th April 2024), MB (13th April 2024), PeeBee (13th April 2024), Touses (14th April 2024)
-
14th April 2024, 05:28 PM
#318
Patrol Freak
well i took it for a trip around the block... manages to hit 500c at about 110 when i lift... got the alarm at 550c
tops out at about 1.4 bar
may need to get this thing tuned
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
MB (15th April 2024), PeeBee (14th April 2024), Touses (15th April 2024)
-
15th April 2024, 06:31 PM
#319
Patrol Freak
does anyone know anywhere in Adelaide that is good at tuning a td42 ?
if its worth doin its worth over doin
-
The Following User Says Thank You to garett For This Useful Post:
-
21st April 2024, 09:14 AM
#320
Patrol Freak
doing the rear bushes and one of the nuts picked up the thread.
hopefully this stops it from pulling left under throttle.(half of the bushes were busted)
this leaves only the rear panhard that isn't new.
if its worth doin its worth over doin
-
The Following User Says Thank You to garett For This Useful Post: