-
6th May 2014, 10:33 PM
#11
Moderator
Originally Posted by
menace 2
he would feed the bar into the slot from the top I would think
LMFAO!!! AB is a Goose!! I tried to tell him that via Text! It was driving him nuts!
You might have to shoot a video for him Janderson
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
The Following User Says Thank You to MudRunnerTD For This Useful Post:
-
6th May 2014 10:33 PM
# ADS
Circuit advertisement
-
6th May 2014, 11:20 PM
#12
Legendary
Nice work! Its always great to see new ideas
-
The Following User Says Thank You to Alitis007 For This Useful Post:
-
7th May 2014, 06:43 AM
#13
Administrator
Originally Posted by
MudRunnerTD
LMFAO!!! AB is a Goose!! I tried to tell him that via Text! It was driving him nuts!
You might have to shoot a video for him Janderson
I just couldn't see it fitting from the top....lol
I know someone who made a box similar to find he couldn't get the bloody bar through on the angle.
-
The Following User Says Thank You to AB For This Useful Post:
-
7th May 2014, 07:54 AM
#14
Advanced
Very smart I like that!
1990 4.2 Diesel SWB Safari MT - 2" lift + long travel shocks, 33" MTs, -35 Steelies, 17000lb winch, Steel bumpers, Rock sliders, Snorkel, CB, Manual hubs, LED lightbar, Rear secure drawer, Rear drop down table, Manual gearbox conversion.
-
The Following User Says Thank You to Barrbeast For This Useful Post:
-
7th May 2014, 03:56 PM
#15
Expert
Originally Posted by
AB
I just couldn't see it fitting from the top....lol
I know someone who made a box similar to find he couldn't get the bloody bar through on the angle.
Hope this works, not done a video on hear before
http://s1070.photobucket.com/user/ja...tml?sort=3&o=0
-
The Following User Says Thank You to janderson For This Useful Post:
-
7th May 2014, 03:59 PM
#16
Expert
hey mate should work out how to wire in a small 12v transfer pump. then you wouldn't need to lift them out at all.
-
The Following User Says Thank You to sil3nt_dr3ams For This Useful Post:
-
7th May 2014, 05:24 PM
#17
Id just open the arm and use a jiggiler hose lol
-
The Following User Says Thank You to megatexture For This Useful Post:
-
7th May 2014, 05:34 PM
#18
Expert
Originally Posted by
megatexture
Id just open the arm and use a jiggiler hose lol
that's all I use, easer than pouring them
-
-
7th May 2014, 06:25 PM
#19
Administrator
Originally Posted by
janderson
Hey mate nah I meant putting the chainsaw in the box...
-
-
7th May 2014, 06:52 PM
#20
Expert
Originally Posted by
AB
Hey mate nah I meant putting the chainsaw in the box...
I just take hole box out as when I'm cutting I do a trailer load in the one spot, mostly anyway. sorry for the miss understanding.
-
The Following User Says Thank You to janderson For This Useful Post: