-
7th May 2013, 11:01 AM
#1
Patrol God
Im Dumb, what bolts for my bull bar?
Yep Im dumb. I left my old bolts out at my parents house. Im going to buy some nice new shiny ones but what type? Is it M16 or something? im dumb about this stuff. I plan to buy the toughest ones i can afford.
I will go get them as soon as i get a serious answer out of one of you (which will be a while knowing you lot! Growlers, Scotty, Winnie, Clunk, Nisshead, Georgina need not reply!!)
Hello from Under Down Under!
-
-
7th May 2013 11:01 AM
# ADS
Circuit advertisement
-
7th May 2013, 11:15 AM
#2
Legendary
Well Lucy if you had a GU i'd say 110% they would be M14x 1.5 zinc coated high tensile bolts with flat and spring washers, the length should be about 30 - 35mm.
They look like this
ImageUploadedByTapatalk 21367887484.437072.jpg
-
The Following User Says Thank You to Alitis007 For This Useful Post:
-
7th May 2013, 11:17 AM
#3
SUCH IS LIFE
HAHAHAHHAHAHHAHA
________________________
______ 2017 D-Max _______
I don't have a short temper. I just have a quick reaction to bullshit
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
The Following User Says Thank You to Maxhead For This Useful Post:
-
7th May 2013, 11:37 AM
#4
Patrol God
Thanks George that looks like the ones!
Next Question: Whats the best type? It would be the ones with the strongest sheer rating? is that even what you call it??
Hello from Under Down Under!
-
-
7th May 2013, 11:38 AM
#5
Patrol God
Originally Posted by
Nisshead
HAHAHAHHAHAHHAHA
Get a job!!
Hello from Under Down Under!
-
-
7th May 2013, 11:44 AM
#6
Legendary
Originally Posted by
taslucas
Thanks George that looks like the ones!
Next Question: Whats the best type? It would be the ones with the strongest sheer rating? is that even what you call it??
High tensile steel is 8.8 t the normal is 7 i think. Normally they're black steel but the zinc coated ones are silver so they don't rust as fast. Stainless would be better coz they're a bit stronger but will cause electrolysis (rust). But when you go to the bolt shop ask to try it in the chassis first to make sure you've got the right thread pitch!
-
-
7th May 2013, 11:46 AM
#7
Sweety dont be so hard on yourself!!!!!!
-
-
7th May 2013, 11:47 AM
#8
Patrol God
Originally Posted by
Bloodyaussie
Sweety dont be so hard on yourself!!!!!!
oh i forgot to put you on the list at the top Jonathan! lol
Hello from Under Down Under!
-
-
7th May 2013, 11:49 AM
#9
Patrol God
Originally Posted by
Alitis007
High tensile steel is 8.8 t the normal is 7 i think. Normally they're black steel but the zinc coated ones are silver so they don't rust as fast. Stainless would be better coz they're a bit stronger but will cause electrolysis (rust). But when you go to the bolt shop ask to try it in the chassis first to make sure you've got the right thread pitch!
Yeah i was just going to go buy one and see if it fits before getting the rest. Ill see what they've got in their limit stocks lol
Hello from Under Down Under!
-
-
7th May 2013, 11:53 AM
#10
Legendary
I forgot your not driving it daily anymore lol just go grab an original from you parents place or use one off the front recovery point to see if they are the same, i think they should be.
-