-
6th May 2016, 07:52 PM
#6471
Patrol God
Started the exhaust lol.. couldn't help myself..
So far so good
-
The Following 3 Users Say Thank You to BigRAWesty For This Useful Post:
jay see (6th May 2016), mudnut (6th May 2016), Roosim (8th May 2016)
-
6th May 2016 07:52 PM
# ADS
Circuit advertisement
-
6th May 2016, 08:07 PM
#6472
Patrol God
Finally got the EGR pipe fitted to the headers.
My advice is: not to follow my advice.
-
-
6th May 2016, 08:16 PM
#6473
Patrol Freak
Originally Posted by
bigguwesty
Started the exhaust lol.. couldn't help myself..
So far so good
How many times did you soak the studs? Good luck!!
2008 GU6 3.0 CRD AUTO | Safari Snorkel | 2" Ironman lift kit | Runva 11XP Winch | 33" MTZ's | Full Length Roof Rack | GME TX3200 | 30" LED Light Bar |
-
-
6th May 2016, 08:19 PM
#6474
Patrol God
Originally Posted by
Bacho86
How many times did you soak the studs? Good luck!!
Ummmmmm. .. twice..
Actually most of em were loose.. which isn't good..
-
-
6th May 2016, 08:25 PM
#6475
Patrol God
Originally Posted by
Bacho86
How many times did you soak the studs? Good luck!!
In 3 hours I've removed pipe work around the turbo, the catch setup, removed actuator to remove the heat shield, remived flex section of exhaust, old dump pipe, tried fitting new dump pipe, had to remove sway bar, fitted dump pipe and so far all good.
Refitted actuator and sway bar..
So tomorrow it should all be smooth sailing..
-
The Following 3 Users Say Thank You to BigRAWesty For This Useful Post:
Bacho86 (6th May 2016), Hodge (6th May 2016), jay see (6th May 2016)
-
6th May 2016, 08:28 PM
#6476
Patrol God
Well done bloke. So far you're way ahead of where I was at that stage. I can't recall removing the sway bar though .
-
-
6th May 2016, 08:30 PM
#6477
Patrol Freak
Originally Posted by
bigguwesty
Ummmmmm. .. twice..
Actually most of em were loose.. which isn't good..
No I wouldn't think so...
Originally Posted by
bigguwesty
In 3 hours I've removed pipe work around the turbo, the catch setup, removed actuator to remove the heat shield, remived flex section of exhaust, old dump pipe, tried fitting new dump pipe, had to remove sway bar, fitted dump pipe and so far all good.
Refitted actuator and sway bar..
So tomorrow it should all be smooth sailing..
Good work, sounds like it's all going to plan then !! When you going to attack the heat shield?
2008 GU6 3.0 CRD AUTO | Safari Snorkel | 2" Ironman lift kit | Runva 11XP Winch | 33" MTZ's | Full Length Roof Rack | GME TX3200 | 30" LED Light Bar |
-
-
6th May 2016, 08:58 PM
#6478
Patrol God
It's out..
Was a carnt.. all the heater hoses over the top of it I have to remove the actuator to get it out..
That's what I've achieved this arvo..
Tomorrow I reinstall the intake and finish the rest of the exhaust fit out..
Dump pipe fit perfectly..
-
The Following User Says Thank You to BigRAWesty For This Useful Post:
-
6th May 2016, 10:22 PM
#6479
I'm not sure
Mounted up the roof top light bar. Now the fun job of wiring it in..
-
The Following 3 Users Say Thank You to Chappy For This Useful Post:
BigRAWesty (6th May 2016), mudski (7th May 2016), threedogs (7th May 2016)
-
7th May 2016, 05:15 PM
#6480
Patrol Freak
What did you do to your Patrol today!
Put the mud tyres on ready for next weekends high country trip!
Sent from my iPhone using Tapatalk
2008 GU6 3.0 CRD AUTO | Safari Snorkel | 2" Ironman lift kit | Runva 11XP Winch | 33" MTZ's | Full Length Roof Rack | GME TX3200 | 30" LED Light Bar |
-