-
11th June 2012, 07:43 PM
#311
-
-
11th June 2012 07:43 PM
# ADS
Circuit advertisement
-
11th June 2012, 10:29 PM
#312
Fitted the new fridge slide that goes with the Engel 50th aniversary gold plated bling edition fridge, started on the wiring install for said fridge, measured up the space that will hold the redarc battery isolator in order to make a mounting plate and thought about where I am going to install the new Ryco fuel/water seperator element to run inline with the existing water seperator. I hate water in me diesel!
-
-
14th June 2012, 10:08 PM
#313
Advanced
ImageUploadedByTapatalk1339673913.673399.jpg
Pulled the spigot bush out with a bolt and paper towel. Works a treat.
-
-
15th June 2012, 10:46 PM
#314
BIG & BALD
Got a 2" lift kit quoted KONI shocks and spring $2200.00
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
-
16th June 2012, 01:09 AM
#315
Started running more wires, reverse light, in cab winch controls, re do the reverse camera. Isolator override switch and aux battery control.
Got half the dash apart and wires every where. Had a mate over to lend a hand, not sure if he was a help or hindrance!
Teno's Troll...
08 CRD ST. 2" lift, 33' Maxis Bighorns, Snorkel, ARB Deluxe Bar with Foggies, 12000lbs Avenger Mako TDS with Synthetic rope.
-
-
16th June 2012, 05:31 PM
#316
Nasty Dog - Moderator
Got 4 wheel nuts to replace the locknuts that I butchered with the hammer and cold chisel two weeks ago and best of all I bought one of these...
[IMG][/IMG]
[IMG][/IMG]
If any members require assistance in anything regarding this forum, just let me know via a PM and I will help you in any way that I can.
-
-
16th June 2012, 08:00 PM
#317
Started work on the roof basket for the Safari, making it big and strong 1.2mx2.4m and 250mm high the bottom trayu is made out of 34mm pipe 3mm side wall and 50x50x4mm steel mesh. The top frame is 25mm pipe with 2mm side wall and 200x250x3 mm plates to join the two togeather
-
-
20th June 2012, 11:24 AM
#318
Advanced
Started installing new custom rear barn door drop down 'work/prep' table. 800x350mm ally plate. Not sure if I'm going to vinyl the underside or leave it, only time will tell.
Here's a quick photo
ImageUploadedByTapatalk1340153601.777359.jpg
ImageUploadedByTapatalk1340153640.225022.jpg
Bad-Trol: 2004 GU3 ST-L. Sent from my iPhone
-
-
20th June 2012, 11:25 AM
#319
Advanced
Also replaced the bonnet gas struts and these ones are POWERFUL! Need two hands to close her now!
No more bonnet falling on my head when working on the donk
Bad-Trol: 2004 GU3 ST-L. Sent from my iPhone
-
-
20th June 2012, 11:52 AM
#320
SPAMINATOR
Originally Posted by
The Dogman
Got 4 wheel nuts to replace the locknuts that I butchered with the hammer and cold chisel two weeks ago and best of all I bought one of these...
just 1?!?!
IF YA DONT GET STUCK YA AINT TRYIN HARD ENOUGH........OR YA TOOK THE CHICKEN TRACK
WARNING: TOWBALLS USED WITH SNATCHSTRAPS DO KILL!!
-