-
14th August 2020, 06:13 PM
#451
Originally Posted by
Mickhead
Seriously tho.. had a Rossi ebay inverter mig for a short time, sold it quickly due to horrid feed and lack of support. Rossi is an ebay brand that sounds nice.. like detroit and chicago trying to be milwaukee..
OK, thanks for clearing that up - thought @MB had slipped into the thread! I will have a look at the Bunnings model instead.
-
The Following 2 Users Say Thank You to PeeBee For This Useful Post:
jay see (14th August 2020), mudski (14th August 2020)
-
14th August 2020 06:13 PM
# ADS
Circuit advertisement
-
15th August 2020, 01:23 PM
#452
Legendary
Well after some googling and taking in the information from you guys and some of the guys at work. I'm pretty sure that I'm going to go with a 135 amp machine.
Reason for this is the 2 people that have these are happy with them mudski (cigweld) and a guy from work(Michigan). Yes a bigger machine probably would be better, but I need to look at the cost as well, anyway if I need to do big long welds and I can't do them at home, I can always get it done at work.
Thanks guys.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
15th August 2020, 06:15 PM
#453
Moderator
Originally Posted by
jay see
Well after some googling and taking in the information from you guys and some of the guys at work. I'm pretty sure that I'm going to go with a 135 amp machine.
Reason for this is the 2 people that have these are happy with them mudski (cigweld) and a guy from work(Michigan). Yes a bigger machine probably would be better, but I need to look at the cost as well, anyway if I need to do big long welds and I can't do them at home, I can always get it done at work.
Thanks guys.
Sent from my CPH1979 using Tapatalk
Hi amte, i have a 140 too. if i was buying again i would go at least a 170 or 200 just to future proof me.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
15th August 2020, 09:49 PM
#454
Tools you have bought/want to buy feedback thread
Originally Posted by
jay see
Well after some googling and taking in the information from you guys and some of the guys at work. I'm pretty sure that I'm going to go with a 135 amp machine.
Reason for this is the 2 people that have these are happy with them mudski (cigweld) and a guy from work(Michigan). Yes a bigger machine probably would be better, but I need to look at the cost as well, anyway if I need to do big long welds and I can't do them at home, I can always get it done at work.
Thanks guys.
Sent from my CPH1979 using Tapatalk
Happy for you to come over, post COVID, and have a play around with my weld if you want. The thing I like about mine it’s not confusing with it’s selections. Wire speed and output voltage selections. Does gaslless too but I have a Cigweld arc welder for that if I need. Bought the trolley on eBay for nix too. Like I said, for what I do and have done. 4wd stuff. It’s been flawless.
Yeah a tig would be great. But I’d very rarely use that I reckon.
Sent from my iPhone using Tapatalk
Last edited by mudski; 15th August 2020 at 10:10 PM.
-
-
16th August 2020, 01:41 PM
#455
Legendary
Originally Posted by
mudski
Happy for you to come over, post COVID, and have a play around with my weld if you want. The thing I like about mine it’s not confusing with it’s selections. Wire speed and output voltage selections. Does gaslless too but I have a Cigweld arc welder for that if I need. Bought the trolley on eBay for nix too. Like I said, for what I do and have done. 4wd stuff. It’s been flawless.
Yeah a tig would be great. But I’d very rarely use that I reckon.
Sent from my iPhone using Tapatalk
Thanks for the offer Mark, but I want one during this lock down period, probably get one during the week. I don't see the need for a bigger amp machine as long as these do the job and that's all I'm after. As stated earlier if it's a big long heavy weld I can get it done at work and even better by professional welder.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
The Following User Says Thank You to jay see For This Useful Post:
mudski (16th August 2020)
-
16th August 2020, 08:34 PM
#456
Originally Posted by
jay see
Thanks for the offer Mark, but I want one during this lock down period, probably get one during the week. I don't see the need for a bigger amp machine as long as these do the job and that's all I'm after. As stated earlier if it's a big long heavy weld I can get it done at work and even better by professional welder.
Sent from my CPH1979 using Tapatalk
Yeah we’ll don’t spend on what you don’t need then. Look on my build thread on the bar work I have done. That’s pretty much the heaviest I will ever do, probably the same for you I will guess, and this welder did it with ease.
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to mudski For This Useful Post:
jay see (16th August 2020)
-
16th August 2020, 08:57 PM
#457
.........
By no means a professional welder myself, agricultural at best Jaysee mate. Can offer only some basic advice until you hone your skills on any given machine, they are all different obviously but same same end game bonding metals at the end of the day?
A good mask will help you focus on the material and what your heat/speed is doing left and right and downwards etc...
There is no point making a perfect looking motion bead atop if the material below is not becoming one (Zen Like :-)
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to MB For This Useful Post:
Mickhead (20th August 2020)
-
16th August 2020, 09:35 PM
#458
Legendary
Originally Posted by
MB
There is no point making a perfect looking motion bead atop if the material below is not becoming one (Zen Like :-)
Sent from my iPhone using Tapatalk
You'll be surprised how many times I see this at work when they are giving a new welder a test run.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
The Following User Says Thank You to jay see For This Useful Post:
-
16th August 2020, 09:44 PM
#459
.........
That’s probably genuine I’m thinking though John Mate! Are they just getting a feel of the new tool before getting stuck into hot work.
Not that I would trust myself to weld on say Vic/Roads approved engine mounts for serious scrutiny but I do try where possible to test my heat & speeds on similar sized plates prior to bastardisation of a paddock implement or two :-)
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to MB For This Useful Post:
jay see (16th August 2020)
-
16th August 2020, 09:55 PM
#460
Legendary
They give them a few runs if they can't set the machine to produce a good weld in all aspects they move them on.
Our work is ADR approved so they're gotta know what they're doing.
I'll get some offcuts in different thickness to play around with at home before I attempt anything that requires strength.
Sent from my CPH1979 using Tapatalk
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
The Following User Says Thank You to jay see For This Useful Post: