OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

User Tag List

Page 4 of 4 FirstFirst ... 234
Results 31 to 34 of 34

Thread: Install/Upgrade to 4" Snorkel (recessed) and new Pod Air Box

  1. #31
    The master farter
    mudski's Avatar
    Join Date
    Apr 2012
    Location
    Eltham North
    Posts
    15,597
    Thanks
    8,667
    Thanked 11,261 Times in 6,427 Posts
    Mentioned
    460 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by Bidja View Post
    Now the 4" induction upgrade complete, went to ECPT (Tuggerah, NSW) last week, put it on rollers and had tune 08 CRD.

    Have been progressively doing build up(last 15months). Stock eng except:

    NADS
    Remap
    Procharge stage 3 h/f turbo
    Tillix/needle (Max B 26psi)/13.5"Hg VNT actuator
    Jonny Tig cooler
    Ben Lipscombe - 9" K&N Pod / 4" thru airbox (3" to turbo)
    4" fwd facing snorkel w/safari air ram
    3" exhaust turbo back w/ muffler and cat

    Had a couple of tunes along the way, latest being after install of JT cooler and 4" induction.
    Running 33" m/t

    Leaned it off from AFR19:1 back to 20:1, could have put more fuel but this has provided a good reliable result:
    136rwkw and 512 N-m/4th gear.

    Dyno results attached, my CRD "Blue Trace" / the "Red Trace" is for comparison purposes of a stock 2010 CRD on 33s and 3" exhaust on the same dyno.

    Achieving 20psi Boost @ 1900-2000 rpm, max B 26psi @ 2200rpm (good to drive).

    With the upgrade to JT cooler and 4" induction gave me an extra 70 N-m. From 378 to 450N-m and with the tune last week now producing 512 N-m. The trip back home from Tuggerah, NSW via Sydney (400km). fuel usage 12.5l/100km.
    Old post but...Jesus John thats pretty impressive. Gotta be happy with that.

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many

     

  3. #32
    Patrol Freak Bidja's Avatar
    Join Date
    Jul 2017
    Location
    Southern Table Lands, NSW
    Posts
    1,089
    Thanks
    1,183
    Thanked 1,006 Times in 565 Posts
    Mentioned
    37 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by mudski View Post
    Old post but...Jesus John thats pretty impressive. Gotta be happy with that.
    She rolls pretty well. Have had some further improvement, especially low down torque, resulting from adjustment to the VNT actuator rod length (reduced "Hg) to hold
    the vanes closed longer so the turbine spins up quicker. Was laggy 4&5th low down due to larger exhaust wheel(Procharge H/F turbo).

    Currently achieving boost 25 psi all gears around 1950 rpm (all out by 2100rpm_26-27psi). Also been trialing max spool (using Tillix only with needle disconnected) and a throttle control unit that has removed a lot of throttle lag (caused by drive by wire_CRD), linear spool. Different dyno (reads a bit lower than previous), but note low down torque improvement_ from 250 to 300 N-m(max nom 530N-m). Always adjusting actuator rod but so close now and will soon go back on rollers, may be a little more fuel early on. Looking at FMIC (still a 600x300mm T&F).
    2008 GU WAG ST Manual CRD - To do the job

  4. The Following User Says Thank You to Bidja For This Useful Post:

    mudski (28th June 2019)

  5. #33
    The master farter
    mudski's Avatar
    Join Date
    Apr 2012
    Location
    Eltham North
    Posts
    15,597
    Thanks
    8,667
    Thanked 11,261 Times in 6,427 Posts
    Mentioned
    460 Post(s)
    Tagged
    1 Thread(s)
    It will be interesting to see a before and after dyno run with a FMIC.

  6. The Following User Says Thank You to mudski For This Useful Post:

    Bidja (28th June 2019)

  7. #34
    Patrol Guru 0-TJ-0's Avatar
    Join Date
    Jan 2017
    Location
    South Australia
    Posts
    623
    Thanks
    572
    Thanked 396 Times in 256 Posts
    Mentioned
    11 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by Bidja View Post
    @0-TJ-0 @threedogs

    Came across a post selling that airbox 4" in and out pod style air box + K&N pod (same as I fitted). Maybe still available.

    PRICE AND PRICE CONDITIONS: $250 + post box only or $300 + post for box and pod

    https://www.patrol4x4.com/threads/sa...-n-pod.407157/

    I paid: box $365 posted + $90 for pod K&N
    Thanks for keeping an eye out mate. Patrol is on hold for a bit while i do some much needed home maintenance unfortunately.

  8. The Following User Says Thank You to 0-TJ-0 For This Useful Post:

    Bidja (28th June 2019)

Page 4 of 4 FirstFirst ... 234

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •