-
15th July 2016, 07:57 PM
#121
Patrol God
Very Nice Mark.
Will have to pop around and have a gander at these. Whens the fitting.
-
-
15th July 2016 07:57 PM
# ADS
Circuit advertisement
-
15th July 2016, 08:37 PM
#122
Patrol God
Safari do a 4" ram head but its around 130-150. If you have dremel go and get a 2mm end mill. They go straight in the dremel chuck and you can cut any which way as long as you have a steady hand. Otherwise grab yourself a nibbler or cheap air hacksaw.
As for the comp cover and as I said earlier just leave the 3" inlet one in place. Just use a short 3-4" straight adaptor in silicon this will be fine.
-
The Following User Says Thank You to nissannewby For This Useful Post:
-
15th July 2016, 08:51 PM
#123
Administrator
Originally Posted by
mudski
Part 2/3 has arrived.... <img src="http://www.nissanpatrol.com.au/forums/attachment.php?attachmentid=68157"/> I'm think to maybe even get a 4-3 adapter for the box to intake pipe fitment, put the snorkel and box in, and then do the rest when I get the comp housing.
Did you specifically order it with the piping on the snorkel side or is that how it turned up?
-
-
15th July 2016, 08:54 PM
#124
Administrator
I'm sure MB wouldn't mind you borrowing the nibbler mate or bring it over one day and I'll cut it for you.
I've cut a few now, nothing better then cutting someone else's panels
-
The Following User Says Thank You to AB For This Useful Post:
BrazilianY60 (27th April 2023)
-
15th July 2016, 10:19 PM
#125
............................
Last edited by mudski; 6th March 2017 at 03:00 PM.
-
The Following User Says Thank You to mudski For This Useful Post:
-
15th July 2016, 10:22 PM
#126
Administrator
Originally Posted by
mudski
The comp cover on it is 2 3/4 not 3 Mat. The GT3071 only has two inlet options. Neither are 3inch. Ill stick with the Donaldson head as Hitachi near by sell them for about $60. And i might get the mill end bit for my dremel... The air box was just the air box and nothing else. The snorkel came with all the bits needed to attach to the air box. Sent from my SM-P600 using Tapatalk
Yeah ok, interesting they now supply a pipe to connect rather then a rubber flange.
I'm glad they listened to customer feedback
-
-
15th July 2016, 10:45 PM
#127
...........................
Last edited by mudski; 6th March 2017 at 03:00 PM.
-
-
15th July 2016, 11:55 PM
#128
Patrol God
Originally Posted by
mudski
The comp cover on it is 2 3/4 not 3 Mat. The GT3071 only has two inlet options. Neither are 3inch. Ill stick with the Donaldson head as Hitachi near by sell them for about $60. And i might get the mill end bit for my dremel...
Sent from my SM-P600 using Tapatalk
Come on mark.... just get a 4"- 2.75" reducer then. Simple.
-
-
16th July 2016, 12:28 AM
#129
.............................
Last edited by mudski; 6th March 2017 at 03:01 PM.
-
-
16th July 2016, 07:43 AM
#130
Administrator
Originally Posted by
mudski
Which part are you refering too? The pipe from the snorkel to the elbow into the air box? Sent from my SM-P600 using Tapatalk
Yep that part, the pipe on the airbox intake
-
The Following User Says Thank You to AB For This Useful Post: