-
11th October 2022, 05:18 PM
#261
Patrol Freak
i got a delivery of suspension parts ... on a pallet
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (12th October 2022), MB (12th October 2022), rusty_nail (11th October 2022)
-
11th October 2022 05:18 PM
# ADS
Circuit advertisement
-
16th October 2022, 01:32 PM
#262
Patrol Freak
fitting new radius arms ... lining up the last bolt is interesting, ratchet strap and jacks make it easier by yourself. found out my shocks were dead panhard bushes gone radius arm bushes gone inner axle seal is gone..
i'm not looking at the rear end ... that can be future garetts problem.
if its worth doin its worth over doin
-
The Following 2 Users Say Thank You to garett For This Useful Post:
MB (17th October 2022), mudnut (16th October 2022)
-
17th October 2022, 10:48 AM
#263
Patrol Guru
When I did mine, a bottle jack on the pinion side of the diff center helped a lot to "fine tune" the alignment of the radius arm and axle housing holes.
-
The Following User Says Thank You to BrazilianY60 For This Useful Post:
-
17th October 2022, 05:09 PM
#264
Patrol Freak
well now i have driven it with the new radius arms and shocks ... no death wobble ... still gunna change more parts as they are not good.
last time i did this i had a hoist ... soo much easier
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (18th October 2022), MB (18th October 2022), Rossco (17th October 2022)
-
30th November 2022, 04:58 PM
#265
Patrol Freak
i may have ordered more parts ...
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (30th November 2022), MB (1st December 2022), mudnut (30th November 2022)
-
2nd December 2022, 06:26 PM
#266
Patrol Freak
parts.jpg
i gotta get around to fitting them but now have a work car, so no rush
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (2nd December 2022), PeeBee (3rd December 2022), rusty_nail (3rd December 2022)
-
12th March 2023, 05:29 PM
#267
Patrol Freak
i got around to cleaning them manifolds up, going to try and paint the exhaust in ceramic. then wrap it,
looking for the fuel pump and a couple more bits, but i think i have most of what i need now.
if its worth doin its worth over doin
-
The Following 3 Users Say Thank You to garett For This Useful Post:
BrazilianY60 (13th March 2023), mudnut (12th March 2023), rusty_nail (13th March 2023)
-
13th March 2023, 12:06 PM
#268
Patrol Freak
well i cleaned it up
exhaust.jpg
if its worth doin its worth over doin
-
The Following User Says Thank You to garett For This Useful Post:
BrazilianY60 (14th March 2023)
-
13th March 2023, 06:40 PM
#269
Daily Lurker
Well done mate. Hope all is well in your world
Sent from my SM-G988B using Tapatalk
-
-
14th March 2023, 03:51 AM
#270
Patrol Guru
What did you use to clean the carbonization inside the manifold?
-