-
18th January 2016, 04:12 PM
#81
Legendary
Originally Posted by
Kimbo63
There will be no problem fitting a tee I done it for my oil pressure gauge as well go check your local hosemasters,pertek or Enzed
Cheers mate.
Will do.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
18th January 2016 04:12 PM
# ADS
Circuit advertisement
-
27th January 2016, 05:01 PM
#82
Legendary
Originally Posted by
Kimbo63
There will be no problem fitting a tee I done it for my oil pressure gauge as well go check your local hosemasters,pertek or Enzed
I've done the drive around and no one stocks a 12x1.25 tee. Hard enough to find anything that's 1.25, so I'm going to tap in a new one here.
1453872593758.jpg
Has anyone got a 1/8 npt tap that I could borrow?
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
31st January 2016, 03:09 PM
#83
Legendary
My gauge should arrive next week, after a mix up on there end. Ive run wires though the firewall and up and under the dash.
Where is the best place to get the +&- for the gauge and what about the light.
Had a search for someone else's install but couldn't find one.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
31st January 2016, 04:31 PM
#84
Patrol God
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
-
31st January 2016, 04:44 PM
#85
Legendary
Originally Posted by
threedogs
Yes, but not for the temp gauge.
Any threads showing how to install.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
31st January 2016, 04:50 PM
#86
Patrol Guru
check these out jay see http://www.ebay.com.au/itm/5-X-ADD-A...YAAOSwa39Uyve7 credit to ET, its what I used to get +ve for my EGT gauge, I had an existing -ve wire connected to one of the bolts behind the centre part of the dash. You can also get those adapters from Repco and SCA however you'll pay a fortune for one.
2004 4.2TDi GU ST Ute, 3" Exhaust, UHF, Lightforce Spotties, BFG All Terrains, Steel Winchbar, Winch, Dual Batts, CC Ultimate IC, 4" Snorkel, XLR8 Steps and Scrub bar
-
The Following User Says Thank You to gubigfish For This Useful Post:
jay see (31st January 2016)
-
6th February 2016, 12:06 PM
#87
Legendary
Wanting to lose the plugs for the dash cam and the GPS. Is there any problems to cut the plugs off and wire them into the accessories somewhere. Don't think it would be a issue, but want to make sure.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
The Following User Says Thank You to jay see For This Useful Post:
lucus30 (6th February 2016)
-
6th February 2016, 01:20 PM
#88
Hardcore
Originally Posted by
jay see
Wanting to lose the plugs for the dash cam and the GPS. Is there any problems to cut the plugs off and wire them into the accessories somewhere. Don't think it would be a issue, but want to make sure.
If they are just 12v power no problem at all.
Lucus30's 1999 GU ST TB45E
-
The Following User Says Thank You to lucus30 For This Useful Post:
jay see (6th February 2016)
-
6th February 2016, 07:17 PM
#89
Legendary
Originally Posted by
lucus30
If they are just 12v power no problem at all.
Thanks mate. I thought it would be fine.
Now to do something about it.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-
-
7th February 2016, 05:09 PM
#90
Legendary
Originally Posted by
lucus30
If they are just 12v power no problem at all.
Another stupid question.
The fuse in the plug is 1amp. The smallest under the dash is 5 amp, do I just disregard it?
Like I've said in the past and continue to prove in the future, I not electronically minded.
12/97 GEE YOU
4.5lt Gas blower. Lots of mods to come.....all in good time.
-