-
29th June 2017, 12:43 AM
#1341
Smart like tractor
Originally Posted by
mudski
He'd have to tow it. The lift and the BIG Treps wouldn't get him out of Melbourne before the fuzz hang a noose around his neck.
Originally Posted by
MudRunnerTD
True story for sure.
Im probably not even keen to head to the high country with it to be honest. If i did it would be Off Grid and Night work and camp during the day out of the way. Will se how it looks when its done lol. Beast mode i reckon.
Well put some road tyres on to drive up on and job done.. The noose will be just as tight on mine and I drove down there..... piss poor excuse
96 GQ coil/Cab
08 G6eT
-
The Following User Says Thank You to Ben-e-boy For This Useful Post:
-
29th June 2017 12:43 AM
# ADS
Circuit advertisement
-
29th June 2017, 08:43 AM
#1342
Originally Posted by
Ben-e-boy
He'd need road tyres and some ratchet straps around the diffs and chassis to lower it. Lol.
-
-
12th November 2017, 08:53 PM
#1343
Moderator
-
The Following 5 Users Say Thank You to MudRunnerTD For This Useful Post:
GQtdauto (12th November 2017), Lights (24th November 2017), MB (12th November 2017), Rossco (12th November 2017), TPC (12th November 2017)
-
12th November 2017, 09:08 PM
#1344
.........
What a weapon Daz, holy hell, well done mate! Now I do fully understand where that top experience/advise comes from!!
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to MB For This Useful Post:
MudRunnerTD (12th November 2017)
-
12th November 2017, 09:31 PM
#1345
.........
And here I was thinking that the ‘HM’ winch acronym meant ‘High Mount’ - more like ‘Hauling Moderator’ ;-)
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to MB For This Useful Post:
MudRunnerTD (12th November 2017)
-
12th November 2017, 09:36 PM
#1346
Patrol God
How much clearance do you have between heat exchanger and highmount? Keep in mind the body will move being on rubber mounts and may cause contact.
-
The Following 2 Users Say Thank You to nissannewby For This Useful Post:
MB (12th November 2017), MudRunnerTD (12th November 2017)
-
12th November 2017, 09:51 PM
#1347
.........
Ouch, top observant view Mat! Fair helpful call Daz, maybe bar forward 10mm needed from pic angle picked up by old mate?
Sent from my iPhone using Tapatalk
-
-
12th November 2017, 10:14 PM
#1348
Moderator
Originally Posted by
nissannewby
How much clearance do you have between heat exchanger and highmount? Keep in mind the body will move being on rubber mounts and may cause contact.
Yeah I have cut the back out of the weld on brace kit and have about 10mm. Should be ok. The bar is just sitting there now but when I.bolt.it up I will make sure it's forward as far as I can get.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
The Following 2 Users Say Thank You to MudRunnerTD For This Useful Post:
MB (13th November 2017), Rossco (13th November 2017)
-
13th November 2017, 05:41 AM
#1349
Administrator
Originally Posted by
MudRunnerTD
Yeah I have cut the back out of the weld on brace kit and have about 10mm. Should be ok. The bar is just sitting there now but when I.bolt.it up I will make sure it's forward as far as I can get.
Should be ok, my IC is about 8-10mm from the brace.
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to AB For This Useful Post:
MudRunnerTD (13th November 2017)
-
13th November 2017, 06:27 AM
#1350
Legendary
Nice one Daz getting there. What is the heat exchanger, is that a water to air thingo for the intercooler ?
Just did a few things with my winch and is all sitting pretty snug now but still has about 10mm clearance. Was better than with the old bar tho the ratchet was sitting bout 1mm off the intercooler which is a bit close for comfort but luckily didn't give any issues.
Sent from my GT-I9506 using Tapatalk
-
The Following User Says Thank You to Rossco For This Useful Post:
MudRunnerTD (13th November 2017)