-
1st January 2021, 06:41 PM
#131
Got my fingers crossed for you Craig.
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to mudski For This Useful Post:
mudnut (20th January 2021)
-
1st January 2021 06:41 PM
# ADS
Circuit advertisement
-
19th January 2021, 10:10 PM
#132
Patrol God
Good news, Folks! The engine builder came over to have a look at the damage. He was happy that the rods were OK. He told me to check the valves by doing the following: rotate the cam until the valves were closed on each cylinder in turn. Fill the ports with petrol and watch for leakage.
All were watertight, except the inlet on #1 cylinder, which wept ever so slightly, which is still good to go.
I am waiting on a head gasket, and will fit it ASAP. Now I just gotta remember where everything goes
Last edited by mudnut; 20th January 2021 at 01:47 AM.
-
The Following 6 Users Say Thank You to mudnut For This Useful Post:
jack (20th January 2021), MB (20th January 2021), mudski (20th January 2021), Plasnart (19th January 2021), rusty_nail (20th January 2021), TPC (20th January 2021)
-
20th January 2021, 07:43 AM
#133
mudnut's 'Old Trol' build thread.
That’s great mate.
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to mudski For This Useful Post:
mudnut (20th January 2021)
-
20th January 2021, 02:36 PM
#134
Patrol God
Hi Craig while the heads off you could clean up the inlet abd outlet ports.
Just rempve any casting marks ans smoooth them out.
Good luck with it mate TD
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
The Following User Says Thank You to threedogs For This Useful Post:
mudnut (20th January 2021)
-
20th January 2021, 03:44 PM
#135
Patrol God
Thanks, TD. The engine builder port and polished the head, then used his vacuum test bench for maximum flow.
-
-
23rd January 2021, 12:37 AM
#136
mudnut's 'Old Trol' build thread.
I think it’s time you hung a Garret hair dryer of the side of that engine while it’s apart mate. While your there and big ass blow off valve too!
Sent from my iPhone using Tapatalk
-
The Following User Says Thank You to mudski For This Useful Post:
mudnut (23rd January 2021)
-
23rd January 2021, 12:42 AM
#137
Daily Lurker
Sorry but I have it on good authority he doesn't need it to leave you td boys in the dust lol. Would be off chops though
Sent from my SM-G965F using Tapatalk
-
The Following User Says Thank You to rusty_nail For This Useful Post:
-
23rd January 2021, 01:12 AM
#138
-
-
4th December 2022, 12:02 PM
#139
Patrol God
I need help, please, to fit a new E locker. If you have experience with fitting the lockers, I will drive to where ever needed in Vic or SA to get it done and will pay for your time. Thank you for your replies.
My advice is: not to follow my advice.
-
-
5th December 2022, 11:13 AM
#140
Originally Posted by
mudnut
I need help, please, to fit a new E locker. If you have experience with fitting the lockers, I will drive to where ever needed in Vic or SA to get it done and will pay for your time. Thank you for your replies.
Which part are you having trouble with Craig???
Have you tried Trident at the Mount (I know nothing about them)? Heywood Auto (I do know about them), i've been told, have fitted several ARB lockers, I know they're different, but it can be done locally. They send the centres to Portland to get done to them what ever it is that gets done and they install it.
I THINK there is a Harrop mob in Ballarat??
-
The Following User Says Thank You to 10G For This Useful Post:
mudnut (5th December 2022)