-
14th December 2013, 08:53 PM
#11
Patrol Guru
Loving this already, it's blokes in the know like you that help us with less mechanical knowledge learn more and give us more confidence to have a go our selves. Just a side note and this applies to everything in life, "over confidence can bring you down or have bad outcomes" Be realistic with what you can do. Keep up the great thread mate!
GQ Snorkle Lockers front n rear
-
-
14th December 2013 08:53 PM
# ADS
Circuit advertisement
-
14th December 2013, 09:14 PM
#12
Originally Posted by
MudRunnerTD
Looks good mate. Can you tell us how much and where you got them from? Were they the same price front and back?
picked up front and rear e lockers for my gq ls2 conversion today $3000 from opposite lock in canberra, $3460 with carrier bearings and frieght .... $frieght was $80 think i got ripped on bearings but dunno will look up part numbers online at some stage.
anyway ill document the install and put it online.
pasted from another thread
-
The Following User Says Thank You to gqmoder For This Useful Post:
MudRunnerTD (14th December 2013)
-
14th December 2013, 09:20 PM
#13
just undid all the bolts for the diff centre and attempted to remove it but can't get it out.
the tie rod is in the way .... looks like i need to drop the tie rod to remove the centre.
-
-
14th December 2013, 10:00 PM
#14
backlash seem to b about 20 deg
-
-
14th December 2013, 10:28 PM
#15
anyone have any idea what the factory recommended backlash is front gq???
-
-
14th December 2013, 11:39 PM
#16
Moderator
Originally Posted by
gqmoder
anyone have any idea what the factory recommended backlash is front gq???
Have you downloaded the factory manual available to you from this site mate? 1200pages fully catalogue a for you mate. I carry it on the iPhone, iPad and the computer winner. If you have not then you have enough posts (25 minimum) go help yourself mate.
If you can't find the backlash I will have a look through for you bud.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
15th December 2013, 10:31 AM
#17
it actually bought me to a holt last night because i think 20 is abit high just going down to get some gear blue now and ill set the backlash so the wear pattern is right in the middle of the crown wheel (ring gear)
-
-
15th December 2013, 10:58 AM
#18
just went got some going to do a wear pattern test.
where do i d/l these manuals from? wouldnt mind checking to see what the OEM specs are
-
-
15th December 2013, 11:01 AM
#19
Moderator
Originally Posted by
gqmoder
just went got some going to do a wear pattern test.
where do i d/l these manuals from? wouldnt mind checking to see what the OEM specs are
http://www.nissanpatrol.com.au -Nissan-Patrol-Manuals-Nissan-Patrol-Software
Or here is a good thread with the links catalogued
All-Nissan-Patrol-Manuals-listed-and-linked-in-one-thread
Last edited by MudRunnerTD; 15th December 2013 at 11:03 AM.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
The Following User Says Thank You to MudRunnerTD For This Useful Post:
gqmoder (15th December 2013)
-
15th December 2013, 11:07 AM
#20
i found the page but i could not find the button to click
-