-
3rd August 2013, 02:35 PM
#1
Rotaredom
What's better, Mitre Saw, Compound Mitre Saw, Slide Compound Saw or Table Saw
Hi guys and girls
I know a few of you guys are builders / tradesmen so can anyone tell me what is better 2 buy, Mitre Saw, Compound Mitre Saw, Slide Compound Saw or Table Saw.
Going to build two wall partition soonish and also in the long term would like to redo our back deck
Cheers
Toddie
Time is never wasted when your wasted all the time
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
3rd August 2013 02:35 PM
# ADS
Circuit advertisement
-
3rd August 2013, 03:06 PM
#2
Patrol God
I would say a compound saw would suit your purposes the best Todd.
Hello from Under Down Under!
-
The Following User Says Thank You to taslucas For This Useful Post:
NissanGQ4.2 (3rd August 2013)
-
3rd August 2013, 03:12 PM
#3
Patrol God
Yep compound saw.
Kallen Westbrook
Owner of
Westy's Accessories
-
The Following User Says Thank You to BigRAWesty For This Useful Post:
NissanGQ4.2 (3rd August 2013)
-
3rd August 2013, 03:16 PM
#4
Rotaredom
Thanks guys
So no real benefit in getting a slide one?
Time is never wasted when your wasted all the time
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
3rd August 2013, 03:23 PM
#5
Hum!!! Seriously I would go for the slide compound saw.
As a furniture builder I would be stuck with a basic compound saw, they are just not that versatile.
-
The Following User Says Thank You to outback For This Useful Post:
NissanGQ4.2 (3rd August 2013)
-
3rd August 2013, 03:26 PM
#6
Originally Posted by
NissanGQ4.2
Thanks guys
So no real benefit in getting a slide one?
There is. When you cut the timber the slide helps with a cleaner cut and add to its reach. Also make sure the blade is not small. Need at least an 8" blade for what you suggest. The small blades are nice but they have limits.
-
The Following User Says Thank You to outback For This Useful Post:
NissanGQ4.2 (3rd August 2013)
-
3rd August 2013, 03:28 PM
#7
Rotaredom
Originally Posted by
outback
Hum!!! Seriously I would go for the slide compound saw.
As a furniture builder I would be stuck with a basic compound saw, they are just not that versatile.
Any brands to stay away from outback, I was looking at either Bosch or Makita.
Its not something that is going 2 be used everyday so I know a cheaper brand will probably still do the job, but I wouldn't mind doing some photo frames and other woodworking later on so also want it to last a while
Cheers
Todd
Time is never wasted when your wasted all the time
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
3rd August 2013, 03:34 PM
#8
Patrol God
Originally Posted by
NissanGQ4.2
Thanks guys
So no real benefit in getting a slide one?
Originally Posted by
outback
Hum!!! Seriously I would go for the slide compound saw.
As a furniture builder I would be stuck with a basic compound saw, they are just not that versatile.
Yeah sorry I only read one compound saw. Yeah definitely go the sliding compound (that's what I had un mind when I said compound).
You cant go wrong with Makita
Hello from Under Down Under!
-
-
3rd August 2013, 03:40 PM
#9
Patrol God
The trouble with the cheaper ones isn't them lasting a long time, it's how precise they are. A cheaper one may not be exact in its angles etc. 1 degree out for a 45 degree cut wont make too much difference if building a deck but will make a lot of difference if your trying to do more precise cuts for picture frames etc in the future
Hello from Under Down Under!
-
The Following User Says Thank You to taslucas For This Useful Post:
NissanGQ4.2 (3rd August 2013)
-
3rd August 2013, 03:41 PM
#10
Bosch or Makita, both made in China anyway. I would go for the Makita but it depends on the price. Also if you decide to do that picture frame work you want some fine teeth lots of them on the blade. With out checking I run about 60 teeth on my fine blades.
Also remember even if you run carbide tip teeth they will get blunt on hard timber.
Also if you get a nice blade for aluminium you can make some nice stuff out of Capral's Qubelok Extrusions.
-
The Following 2 Users Say Thank You to outback For This Useful Post:
NissanGQ4.2 (3rd August 2013), threedogs (3rd August 2013)