-
11th September 2013, 06:30 AM
#41
BIG & BALD
Originally Posted by
nipagu7
hi guys .
I bought the runva 11000 xp . I think it will be the only runva that will fit as I only have 27mm of clearance between the winch motor and the chassis . I have a 2011 gu7 with arb steel bar . I checked the specs for the other runva's but the motors were longer and not able to be fitted to my car .
I can tell you now that the Runva EWX12000 will fit on an ARB deluxe steel winch bar.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
The Following User Says Thank You to MEGOMONSTER For This Useful Post:
cgm (13th September 2013)
-
11th September 2013 06:30 AM
# ADS
Circuit advertisement
-
18th September 2013, 10:11 PM
#42
BIG & BALD
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
-
18th September 2013, 10:21 PM
#43
Moderator
Originally Posted by
MEGOMONSTER
Surprised you went steel wire rope Mick, make sure you consider that when you organise your front springs when you do the lift mate. There is an extra 15kgs probably in that wire rope. Also make sure you buy at least 1 winch dampened, 2 would be better.
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
18th September 2013, 10:35 PM
#44
CERTIFIABLY INSANE
Originally Posted by
MudRunnerTD
Surprised you went steel wire rope Mick, make sure you consider that when you organise your front springs when you do the lift mate. There is an extra 15kgs probably in that wire rope. Also make sure you buy at least 1 winch dampened, 2 would be better.
I thought you went for the Dyneema......
Tip tip tip......tap tap tap....
1997 GQ Patrol RX, TB42E. Mods: OME 2" lift, 33" BFG KM2'S, ARB winch bar & reconditioned X9 Superwinch, IPF 900 spotties HID conversion, ARB side steps and scrub bars, Kaymar rear step & spare wheel carrier & jerry holder, Rear 55W LED worklight, Safari Snorkel, 147L LRA tank, Extended diff breathers, dual batteries, GME UHF, Home built drawer and fridge slide, ARB 60L fridge.
-
-
18th September 2013, 10:53 PM
#45
BIG & BALD
Originally Posted by
MudRunnerTD
Surprised you went steel wire rope Mick, make sure you consider that when you organise your front springs when you do the lift mate. There is an extra 15kgs probably in that wire rope. Also make sure you buy at least 1 winch dampened, 2 would be better.
I did go dyneema but the spastics sent me a wire winch with the rope and hawse separate. They still need to change it over.
So I'll have a cable for sale soon.
ARB are giving me a dampener.
Last edited by MEGOMONSTER; 18th September 2013 at 11:18 PM.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-