-
15th May 2014, 02:51 PM
#321
The 747
Originally Posted by
lhurley
could it not be longer to fit a larger shackle?
Look at the picture, the hole is cut to match the hole behind it.
-
-
15th May 2014 02:51 PM
# ADS
Circuit advertisement
-
15th May 2014, 02:54 PM
#322
Patrol Freak
Originally Posted by
Winnie
Look at the picture, the hole is cut to match the hole behind it.
Der... woops
1999 GU DUAL FUEL 4.5 - 2" OME - 33's KM2s - SNORKEL - CUSTOM DINTS.... Goes by the name Candy (the car not me
)
-
-
15th May 2014, 04:14 PM
#323
John, don't most Bullbar mounting kits put a bolt through that tie down point?
Well, at least mine seems to.
Would these still fit?
Between Patrols ATM. Had a beaut GU with 6.5 Chev TD. Next is a GU ute with a 4.5 litre Cummins conversion and a camper on the back.
-
The Following User Says Thank You to FNQGU For This Useful Post:
threedogs (15th May 2014)
-
15th May 2014, 04:35 PM
#324
Patrol God
The profile is the same as what is already there., would be ideal if as you say you could use the larger shackle
bit of work with the die grinder, two smaller shackles with a bridle sounds better
@ BenK not for all then hey
Might only be for the tricky motor/bar combo. Keep ideas coming
Looks like my quest for a one fits all wont happen, but at least I have all models covered
Last edited by threedogs; 15th May 2014 at 04:53 PM.
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
The Following 4 Users Say Thank You to threedogs For This Useful Post:
Alitis007 (15th May 2014), Avo (16th May 2014), Clunk (15th May 2014), growler2058 (15th May 2014)
-
22nd May 2014, 07:26 PM
#325
Administrator
Finally ordered some front recovery points off threedogs...
Happy to admit I have been running the gauntlet for too long!!!
-
-
22nd May 2014, 07:38 PM
#326
Hardcore
Originally Posted by
AB
Finally ordered some front recovery points off threedogs...
Happy to admit I have been running the gauntlet for too long!!!
Great stuff mate. Next time I'll pull you out of aeroplane with them. Nah probably good the yota came along not sure you could have stopped if I snatched you out from the front
Lucus30's 1999 GU ST TB45E
-
-
28th July 2014, 02:57 PM
#327
Patrol Guru
Just finished fitting a pair of Threedogs recovery hooks to my GU IV 4.2 tdi with a Nissan winch bar.
The Bull bar mounting bracket required some trimming with the angle grinder and the bolt hole through the tie down point needed a bit of reeming.
I used 50mm M12 high tensile (8.8) bolts 1.25 thread, got them from Repco, but Bunnings or any other hardware shop should have them. The original M12 (8.8) bolts are only 35mm long, not long enough. All up about 40 minutes for this old phart to fit. The two forward bolts screw into captive nuts, the bolt through the tie down hole (rear bottom) has a nut and big washers.
Last edited by TimE; 28th July 2014 at 02:59 PM.
Time Marches On .....and on ..... and on
-
The Following 2 Users Say Thank You to TimE For This Useful Post:
Avo (28th July 2014), threedogs (28th July 2014)
-
28th July 2014, 03:29 PM
#328
Patrol God
good to see you got them fitted looks like I need to modify a touch by scalloping out a small bit.
Some they go straight on others need a bit of a grind, but good thing is they ain't going anywhere
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
-
28th July 2014, 03:32 PM
#329
Moderator
Originally Posted by
TimE
Just finished fitting a pair of Threedogs recovery hooks to my GU IV 4.2 tdi with a Nissan winch bar.
The Bull bar mounting bracket required some trimming with the angle grinder and the bolt hole through the tie down point needed a bit of reeming.
I used 50mm M12 high tensile (8.8) bolts 1.25 thread, got them from Repco, but Bunnings or any other hardware shop should have them. The original M12 (8.8) bolts are only 35mm long, not long enough. All up about 40 minutes for this old phart to fit. The two forward bolts screw into captive nuts, the bolt through the tie down hole (rear bottom) has a nut and big washers.
hey Time, do you reckon you could change the writing to White on that pic as i am colour blind and simply cant read it mate, its a blur.
Cheers bud
Its a Nissan! =====> Its a Keeper!! ....... Got a TD42 in it BONUS!!
....... I'm a lucky bugger! I've got 2 of em!
Check out my Toy -->
MudRunnerTD's GQ From the Ground Up
Originally Posted by
Rogue Dung Beetle
Wish it was Nissan though, Toyotas just can't keep up with the Pootrol pace.
The only good thing about an 80 series is..... the front end?? Wrong!!, the Engine?? Wrong!! the Full Time 4WD system?? Wrong!! Its the NissanPatrol.com.au stubby holder fitted over the transfer lever.
WARNING: Towballs used for recoveries can, and do kill people and damage property.
-
-
28th July 2014, 03:48 PM
#330
Patrol Guru
Originally Posted by
MudRunnerTD
hey Time, do you reckon you could change the writing to White on that pic as i am colour blind and simply cant read it mate, its a blur.
Cheers bud
Yeah it is a bit blury, but click on the pic, then click on the magnifying glass at the bottom right of the pic, then clcik on "view original" magnifying glass that is also on the bottom right of the pop up pic, should now be readable. The text on the pic is basically the same as in the post. Hope that makes sense.
Last edited by TimE; 28th July 2014 at 03:55 PM.
Time Marches On .....and on ..... and on
-