-
11th September 2015, 07:51 PM
#171
BIG & BALD
Also catch can has been fitted and plumbed.
What are your thoughts.
Air Locker has been plumbed and connected.
Also double Anderson plugs on bullbar connected to both primary and aux battery for my solar panel connection.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
The Following User Says Thank You to MEGOMONSTER For This Useful Post:
-
11th September 2015 07:51 PM
# ADS
Circuit advertisement
-
11th September 2015, 07:57 PM
#172
Legendary
Looks awsome mego. Just out of interest is there any reason they coiled up the air line 4 the locker?
-
The Following User Says Thank You to Rossco For This Useful Post:
MEGOMONSTER (11th September 2015)
-
11th September 2015, 09:01 PM
#173
..........
Is the compressor in the spot where the catch can would normally be installed?
-
The Following User Says Thank You to TPC For This Useful Post:
MEGOMONSTER (11th September 2015)
-
11th September 2015, 09:15 PM
#174
BIG & BALD
Originally Posted by
Rossco
Looks awsome mego. Just out of interest is there any reason they coiled up the air line 4 the locker?
I asked that question too, but I arrived after all the techs went home. So never got a real answer.
Salesman said for when they tee off for a rear locker.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
-
11th September 2015, 09:17 PM
#175
BIG & BALD
Originally Posted by
TPC
Is the compressor in the spot where the catch can would normally be installed?
Yes that's correct. Was difficult to have both in that position.
And I didn't want the compressor inside the Trol.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
-
11th September 2015, 09:52 PM
#176
..........
Originally Posted by
MEGOMONSTER
Yes that's correct. Was difficult to have both in that position.
And I didn't want the compressor inside the Trol.
I have been trying to find a spot for a compressor but have the catch can in that spot, took me forever to getting around to fitting it so not likely to move it.
-
The Following User Says Thank You to TPC For This Useful Post:
MEGOMONSTER (11th September 2015)
-
12th September 2015, 11:37 PM
#177
BIG & BALD
Either my winch motor or solenoid has shit itself.
I was testing the winch before leaving for Walhalla in the morning.
I winched out and stopped.
No in and no out.
2011 GU8 ST 3.0 CRD, ARB Bullbar with IPF spotties, scrub bars and side steps, Snorkel, Dual Battery system, Waeco fridge, Turbo Timer, ARB Roof Rack with 5 IPF spotties across the front, Custom full Leather Bucket seats, DPchip, 3" Taipan exhaust, ARE Intercooler & scoop, Autron EGT/Boost and dual volt gauges, ARB front locker.
-
-
13th September 2015, 12:04 AM
#178
Originally Posted by
MEGOMONSTER
Either my winch motor or solenoid has shit itself.
I was testing the winch before leaving for Walhalla in the morning.
I winched out and stopped.
No in and no out.
i was doing some thinking after you called me Mick. Depends on how far you want to go with this now, but if you disconnect the leads from the solenoid to the winch motor and use jump leads from the battery and direct to the motor and the motor turns, then you know its the solenoid and the motor is o.k. if you put pos to pos and neg to neg the motor will turn one way, then go neg to pos and pos to neg on the motor and it will run opposite.
Low voltage supply can also be the issue like we discussed. But it could be just dirty contact in the solenoid. Not what you need the night before a day out hey...
Sent from my SM-P600 using Tapatalk
-
The Following User Says Thank You to mudski For This Useful Post:
MEGOMONSTER (13th September 2015)
-
13th September 2015, 02:49 PM
#179
Patrol God
It a relatively new winch eh only about 6 months old if that.
how savage have the bog hole and river crossing been, I
thought the Runva was waterproof mabe hopefully just a clean
just looking at your terminals all neat and all, would battery terminal spray help,
Last edited by threedogs; 13th September 2015 at 02:52 PM.
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
The Following User Says Thank You to threedogs For This Useful Post:
MEGOMONSTER (14th September 2015)
-
13th September 2015, 02:56 PM
#180
Patrol God
Originally Posted by
TPC
I have been trying to find a spot for a compressor but have the catch can in that spot, took me forever to getting around to fitting it so not likely to move it.
real estate at a premium under the bonnet I take it, cant shuffle a few things around , what about up inside the bullbar wings.
I nearly got a bare bullbar years ago and was going to weld the wings in and make an air tank lol.
Im fitting a long air horn inside my wings
04 ST 3lt auto, not enough Mods to keep me happy, but getting there
-
The Following User Says Thank You to threedogs For This Useful Post:
MEGOMONSTER (14th September 2015)