OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Bidja

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Grill will go back on without mod, might cut out...

    Grill will go back on without mod, might cut out some blanking sections around center badge. Pushing a/c condenser back and keeping FM cooler close to radiator spt panel, recon might even have room...
  2. Pdi fm install done

    There U go for those intertested. Drives well and like to leave off grill.
  3. Various install pics of PDI FM

    Various install pics of PDI FM
  4. Pwr steering cooler flipped, relocated and brkt...

    Pwr steering cooler flipped, relocated and brkt mods
  5. Factory Bar Mount and Center Brkt mods

    Factory Bar Mount and Center Brkt mods
  6. PDI install finished

    The A/C condenser was lifted and moved back so the condenser (driver side) bottom loop would not fowl the cold side piping and made up new bottom brkts each with rubber isolator.
  7. Rectified A/C condenser pipe lower loop fowling...

    Rectified A/C condenser pipe lower loop fowling cooler outlet(refer post 24).

    Air Con Condenser Re-position (lift and pushed back towards radiator)
    Have been a bit concerned with modifying the...
  8. To fit the PDI FM cooler_Need to fit new center...

    To fit the PDI FM cooler_Need to fit new center brkt under bonnet latch, down to the bottom radiator spt member and mount the Pwr steering cooler behind this brkt. I flipped the power steering...
  9. As shown above, had proposed to flip the FM...

    As shown above, had proposed to flip the FM cooler because the hot side tank 2.5" outlet (low on drivers side) fowled with the A/C condenser pipe(bottom loop). Did not like flipping cooler at all so...
  10. FMIC Install_Finished doing some slight mods to...

    FMIC Install_Finished doing some slight mods to the factory bull bar mounts and cutting in hot/cold induction pipe entries to accommodate the PDI bar and plate cooler. Working on re-positioning pwr...
  11. Some do remove EGR assy. DI/CRD _ Not sure if...

    Some do remove EGR assy.

    DI/CRD _ Not sure if has to be electrically connected or not though_try it as stated 0-TJ-0 .
    DI can be physically blocked_no fault code.

    CRD may give fault code_need...
  12. Replies
    279
    Views
    13,661

    Poll: Will not be changing my mind now, started...

    Will not be changing my mind now, started removing bits today to make way for FM install. Be thinking of you guys, have a real good one (will find me in the shed cutting away).
  13. Replies
    3
    Views
    123

    Simon, NADS is good option for both DI and CRD as...

    Simon, NADS is good option for both DI and CRD as mudski stated. If you are able, suggest U choose the CRD if it is a good costed runner and consider installing NADS that suits in time.
  14. Thread: 2008 gu

    by Bidja
    Replies
    1
    Views
    168

    Same vehicle (since new) 170,000kms and have had...

    Same vehicle (since new) 170,000kms and have had no real problems.
    Installed NADS @ 60,0000 kms. Only 10% city driving/live rural, EGR pipe split @150,0000kms (no issue for me).
    Have always...
  15. Have got hold of the FMIC drawing and have...

    Have got hold of the FMIC drawing and have measured up factory bull bar mounts and would need to cut away a bit off factory bull bar mount "rear stay/gusset" above chassis rail to fit cooler(Aft of...
  16. Yes thought snorkel was the intended word(all...

    Yes thought snorkel was the intended word(all good).

    Cooler inlet/outlet placement is my major concern. The cooler I am looking at also has entries @ bottom of tanks and is reason for need to...
  17. ??? Induction sizing all the way to turbo inlet?...

    ??? Induction sizing all the way to turbo inlet?

    Query re_flipping cooler mate:
  18. MudRunnerTD Well 4" and very busy but you...

    MudRunnerTD


    Well 4" and very busy but you got thru. Did you only dry clamp(no sealants)?

    Reason for 4" (hot/cold side) in lieu of say 2.5" (hot side)/ 3"(cold side)? Propose to use 2.5"...
  19. So you removed the thermo fan and all was good? ...

    So you removed the thermo fan and all was good?

    Might disconnect mine and see how she goes before do install.
  20. 0-TJ-0 Looking at possible removing thermo fan. ...

    0-TJ-0 Looking at possible removing thermo fan. Nice job by the way mate
  21. Mate, when did you purchase your Raslarr stuff...

    Mate, when did you purchase your Raslarr stuff and was the powder coat patchy/not thick enough or damaged(from impact)?
  22. A few kits starting to get out there. In my cases...

    A few kits starting to get out there. In my cases the vertical spt strut (genuine) also will have to go and a new brkt fixed in place. The steering cooler is generally shifted to new location, but...
  23. Poor powder coat that would be disappointing...

    Poor powder coat that would be disappointing (especially new) and them not wanting to be bothered with follow up. Will address this when I call them.

    Have a Millweld rear bar, not sure if Mill is...
  24. FMIC Install and Suitable Bull Bar_08 GU IV CRD

    Looking at doing a front mount (bar & plate) cooler(600x300x76mm) install for my GUIV CRD wagon. Looking at replacing the bull bar as not keen on modifying the Genuine Nissan bar mounting brkts...
  25. Replies
    433
    Views
    35,158

    @MB Del's shack, will feel so secure and someone...

    @MB
    Del's shack, will feel so secure and someone else looks pretty keen as well. Good stuff mate.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4