OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: jff45

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    25
    Views
    563

    I'd like to have seen a bit more enthusiasm..

    I'd like to have seen a bit more enthusiasm..
  2. Replies
    30
    Views
    1,226

    Winding the boost controller in to shut off flow...

    Winding the boost controller in to shut off flow should be the same result as blocking flow to the actuator. Also same as blocking the inlet side of controller.
  3. Replies
    2
    Views
    182

    GVM should be stamped on your VIN plate. Nissan...

    GVM should be stamped on your VIN plate. Nissan donít state a GCM so GCM = GVM + towing capacity which will be written on your vehicle somewhere.
  4. Replies
    30
    Views
    1,226

    That's why I was suggesting testing boost...

    That's why I was suggesting testing boost directly with the wastegate firmly shut. If the spring is broken inside the actuator, although I've never heard of that on any forum, you should be able to...
  5. Replies
    30
    Views
    1,226

    Ok, in fact, if you have a boost leak in the...

    Ok, in fact, if you have a boost leak in the system then it will be down on boost anyway.
  6. Replies
    30
    Views
    1,226

    Not quite. What Iím suggesting is to read the...

    Not quite. What Iím suggesting is to read the boost thatís coming directly from the turbo to eliminate any issue with the wastegate.

    On the turbo compressor housing there will be a barb where the...
  7. Replies
    30
    Views
    1,226

    Connect the gauge hose directly to the compressor...

    Connect the gauge hose directly to the compressor housing outlet and remove the hose on the wastegate actuator.
    Donít go silly with it in case it boosts high before it overcomes the actuator spring...
  8. Replies
    30
    Views
    1,226

    Have you taken a reading directly from the...

    Have you taken a reading directly from the compressor with the wastegate firmly closed?
  9. Replies
    10
    Views
    356

    Best mod by far was converting the TB45E auto to...

    Best mod by far was converting the TB45E auto to TD42T auto with the Nomad valve body then adding the Rueben Bauer 11mm IP with a P4x4 TD05 18G.
    $7k conversion doing it all myself and selling the...
  10. This is the retractor in place in the cavity in...

    This is the retractor in place in the cavity in the pillar with the bent bracket. Just get it so the belt is pulling nice and straight before fixing it with the roofing screws or whatever..


    84160
  11. Thought this might interest anyone whoís thinking...

    Thought this might interest anyone whoís thinking about replacing the GU seatbelts. I changed the passenger side today and took a few pics.

    I ordered the receiver with the bent leg but itís bent...
  12. I’ve just ordered new front seat belts from Seat...

    I’ve just ordered new front seat belts from Seat Safe. Part No 114-7554. They can supply the buckle receiver that bolts to seat with a kink in it like the original.

    I asked why they don’t supply...
  13. Replies
    6
    Views
    271

    My mistake, MAF has 12v not 5v. Confusing it with...

    My mistake, MAF has 12v not 5v. Confusing it with TPS.

    This is the diagram from the factory manual.


    84113
  14. Replies
    8
    Views
    468

    Looks like a good guess to me. If the original...

    Looks like a good guess to me. If the original boost hose for the pump compensator is no longer there then you can take it from the manifold with that plate & barb.
  15. Replies
    6
    Views
    271

    If the MAF sensor isn't the problem then it's...

    If the MAF sensor isn't the problem then it's likely to be an issue in the wiring circuit or the plug. You'll need to check that the MAF is getting a 5v signal and, if so, check that the varying...
  16. Replies
    13,732
    Views
    1,678,188

    Sticky: I've had nothing but good experiences with...

    I've had nothing but good experiences with Sparesbox. They were also the cheapest when I recently bought my slotted rotors.

    A few years ago I ordered different sizes of those black nylon P clips...
  17. Replies
    905
    Views
    71,075

    Iíve got an adapter to fit the 20v Xfinity (Aldi)...

    Iíve got an adapter to fit the 20v Xfinity (Aldi) 4.0 a/h to my Ryobi tools. I've also got one of those caulking guns to save the old hands..
  18. Replies
    5,168
    Views
    594,241

    Get the pre-rego GVM upgrade done so it's valid...

    Get the pre-rego GVM upgrade done so it's valid in every state.
  19. Replies
    13,732
    Views
    1,678,188

    Sticky: I have to agree with this. Like a lot of...

    I have to agree with this. Like a lot of caravaners I have my solar panel supports glued on with Sikaflex. Iíve never heard of anyone screwing them on through the roof of the van.
    Took me a weekend...
  20. Replies
    5
    Views
    272

    Mate, you shouldn’t need pics if you take a look....

    Mate, you shouldn’t need pics if you take a look. Take the cover off and unscrew around the sender unit and take the lot out.
    It will give you room to get your hands in there to clean if needed....
  21. Winding the retractor reel is actually quite easy...

    Winding the retractor reel is actually quite easy once you get the pin out and pull the webbing away from it.
    I just followed the Ďhow toí that Cremulator posted earlier on and thereís absolutely no...
  22. Winding up the retractor doesnít work because it...

    Winding up the retractor doesnít work because it still gets slowed going through the top slot on the pillar. If you play with the webbing between that slot and the retractor it works really well. The...
  23. I did my driverís side seatbelt today, took the...

    I did my driverís side seatbelt today, took the pin out and wound it tighter, washed and dried it and still doesnít work as it should. The only thing that really helped was silicone spray on the...
  24. Replies
    5
    Views
    272

    Through the floor in the rear.

    Through the floor in the rear.
  25. Replies
    10,086
    Views
    1,240,886

    Giving it a rad flush and switching from green to...

    Giving it a rad flush and switching from green to red coolant. I didnít know they did a diesel specific coolant until I recently did a search to see what Nulon was offering now.

    If this stuff...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4