Search:

I got a new Dtronic chip never fitted for $150 works excellent

I have tried to search this and found everything but,

So here it is "i am considering removing the clutch fan from my ZD30DI and using a thermo fan instead using the existing electrical clutch fan...

Cool and thanks guys i am new to this sort of stuff Harley's are my game i took this of the wife because of some of the problems, and got her a new ST Navara anyway i took a punt and installed the...

Ok cool i was just under the impression the the ecu would try to operate it, as it plugs into the electrics and as one of the pipes for the vacuum is snapped off, and will not be able to loop the two...

Cheers

thanks i do understand that but at the moment i don't think it will block off securely and may cause engine faults, so i decided the best way was to get a new one, then when i block off the...

I think i have found the reason for the turbo spooling up later, i did notice two days ago that a pipe on the vacuum solenoid (that goes to the VNT) was broken and it had been glued into place, so...

Hey Thanks all, Yes it was concerning for me as well

Yer i do have a spare second pyro, so i may consider installing or i might change the probe and use it as a digital boost gauge, yet to decide...

Now i have read that i can and should read the air temp pre-turbo so i was also wondering should i plum my seconded probe into the inter-cooler pipe before the turbo to read the air temp before it...

Ok i think i found the problem, i had a setting set at 1000 instead on 00000 which now gives me EGTs at an average on a quick test drive not exceeding 345 C this gauge must have not been set or i...

no i checked it a few times it shows it in Cel

well i hope i have set the gauge wrong, but that's what i am seeing at the moment. i think i need to get a infra red thermo reader to ensure the readings i am getting are correct

no these are post readings, unless i have stuffed up the settings on the gauge, but i don't thinks so, as i am 4-5 hours from my nearest dyno but i hope to have it there soon, its a risk i have to...

yes i am just waiting for the needle valve to arrive so i can install it them, i assume it being like it for a while we had the head done about 18 months ago and now trying to do the NADS conversion,...

Would like to information please,

started on the NADS conversion, just installed a 3 inch X-Force exhaust systems with a PYRO and Gauge (AUBER INSTUMENTS) I have the EGR block off plate but not...

Sorry M8 not knowing what you are driving I guess it was of me to assume you we're driving a gu as reference was made to a gu clutch so for my input yrs and a gq does not have a dual mass

Hi

What size probe do you have, I have a spare screw in type 1/8 NPT to suite a 3 mm probe, u just have to drill a hole and tape it into yr dump pope then screw in with some thread lock if this...

Hi

My advice that i can give is what I myself use when looking to buy another vehicle, I look at the condition of the unit, work out what repairs need to be carried out and what costs it would in...

I had a very similar problem and about 2 months later the dual mass flywheel let go, so I then converted to a solid flywheel and pressure plate conversion, if its anything like mine were I had to...

thanks for the link i will read the posts

Hi tried searching the forum

So i am looking to install a diesel chip, on my 01 GU Patrol ZD30DI, was going to go with a chipIT chip, but after a week of waiting for them to reply to some...

If all else fails, I would recommend also having yr turbo checked, i was having a simular problem with hi temps and hi fuel consumption, so i replaced the water/oil cooled (Garrett), with just an oil...

Hi all

I am out at Merredin, and always looking to have some un when i am off so if there are any get together's or fishing trips i would mind tagging along if i am off

PT

The best i can recommend you do is contact the ACCC or the department of Fair Trading in SA or You have The Motor Traders Association (MTA) and inform them of whats happen, they will take the case on...

To remove the airbag from a gu patrol is quite easy simple disconnect the positive cable from the Battery (s) wait about 5 minute for the electrical system to DE-engergise the electrical system,...

Thanks all
for the warm welcome

I am running a standard exhaust, i am looking to install a chip and 3 inch exhaust in the next few weeks, i have a boost gauge installed and my Dawes valve should...